How to proceed with patent India/US?

How to proceed with patent India/US? What are the differences between them, which one is easier to apply?

02 March 2018 5,458 2 View

How can one measure the accuracy of airflow and temperature measurements?

Any suggestions on how to measure an air velocity of 40-100 cm/sec.

09 October 2014 3,884 9 View

How to identify the "Quality of a journal'

07 August 2014 8,153 4 View

Why is Entropy the preferred tool for optimization over the related MCDM tool?

Please enrich us by sharing your knowledge.

05 June 2014 8,640 1 View

Abstract of a thesis.

Is it required to include all results in the abstract?

04 May 2014 10,013 5 View

What is the best convergence limit for natural convection?

In a natural 3D convection problem, if u,v, and w are not converging though energy, is (t) term converging? Can any one please suggest the limit of convergence?

02 March 2014 4,207 3 View

What percentage of radiation contribution in thermally and hydrodynamically fully developed flow in mixed convection?

On what condition can the contribution of radiation can neglected? How do you quantify its contribution?

02 March 2014 2,749 3 View

Is it necessary to incorporate all results in PhD thesis?

As to improve the probability of acceptance of a paper in journal, many results need to be shown. At the same time to avoid the similarity between consecutive papers for different condition...

02 March 2014 8,357 12 View

Does anyone have access to these old papers?

http://www.sciencedirect.com/science/article/pii/0142727X89900453 http://www.sciencedirect.com/science/article/pii/0142727X9290038B

02 March 2014 182 4 View

Collaboration work on CFD?

Anyone needs a visiting research scholar to work part time...or would like to do some collaborative work on heat transfer/fluid flow? Please let me know.

31 December 2013 3,456 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View