Problem in cohesion section in Mohr Coulomb material model in Abaqus?

04 April 2018 0 2K Report

How do i obtain the relation between cohesion yield stress vs absolute plastic strain in Mohr-Coulomb material model in Abaqus?

Badges
Science topic

More M. Wasif Naqvi's questions See All

How to obtain digital elevation data in ascii format?

I have couple of questions how to obtain digital elevation data in ascii format how to covert the above data obtained from usgs website or any other (in format like tif etc) into ascii format for...

01 February 2019 4,220 4 View

What are current research trend in landslide area of Geotechnical engineering?

What are the current innovative topics of research related to landslides and also the modern techniques of landslide prevention?

06 July 2018 9,675 1 View

Does Abaqus pose troubles in solving the problems of cohesionless soils?

I am trying to solve a problem of cohesionless soil using Mohr coulomb material model in abaqus. The problem does not converge and the analysis giver error if i provide minimum or no value of...

03 April 2018 1,306 9 View

Interaction between tunnel lining and soil in abaqus?

What is the interaction property to be assigned between tunnel lining and soil in Abaqus? There is a paper which discusses about interaction between soil and shortcrete and then shortcrete and...

03 April 2018 9,627 2 View

What is the current status of the project,?

I am interested in this topic. Are there any publication?

01 January 1970 3,181 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

Microtome tissue sectioning - How to prevent chatter of paraffin tissue specimen sections?

Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...

06 August 2024 666 4 View