#SEM #PLS-SEM #JASP #Smart-PLS
low R-value is probably related to the higher symmetrical site occupied by Eu3+ ions, supporting the highest emission intensity.
10 June 2024 338 1 View
I would like to apply strong causality test for my panel ARDL, but the software does not take into account the coefficient of the error correction term. when I proced by the the "STEPLS Method"...
14 May 2024 2,561 6 View
I'm looking for public databases for green finance indicators, which provide information on sustainable investments, carbon emissions, sustainable development initiatives, and other indicators...
13 April 2024 3,361 3 View
template [1] auteur1 initial1, Auteur2 initial2, ...., auteur6 initial6 et al year journal name (abbreviation) volume (bold) page
05 November 2023 1,489 3 View
We are looking for temperature variations in shallow aquifers (fresh water) and deep aquifers (saline water) in ganga plane. If there is any relevant data or papers, kindly share. Bests regards...
06 August 2023 9,115 1 View
non
10 March 2023 8,918 0 View
Precision-based ranked retrieval evaluation metrics from information retrieval (IR) such as Precision@k (P@k), AveragePrecision@k (AP@k), and MeanAveragePrecision@k (MAP@k) employ only oracle or...
25 December 2022 3,024 4 View
A doctorate subject of ours requires us to have us publish our work as part of the subject requirement...
10 December 2022 200 2 View
I have a the absorption spectrum + the emission spectrum. I need to calculate the JO parameters for Tm3+ doped phosphors
30 October 2022 6,621 0 View
Please, how can I calculate the total current (or global i) from the capacitive cyclic voltammogram (CV curve as shown in the attached figure)? Thank you in advance.
17 October 2022 4,190 1 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...
07 August 2024 5,343 2 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...
05 August 2024 9,637 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View