01 January 1970 4 8K Report

We need a resource person to take online sessions in Structure Equation Modeling.

More Dr Minakshi Rana's questions See All
How to do pca analysis of c-alpha atom of the protein?

i m interested in pca analysis of c-alpha atoms in gromacs for that i used the following gmx_mpi covar -s mdca.tpr -f mdca.xtc -o eigenvalca.xvg -v eigenvecca.trr -av average.pdb -n index.ndx but...

30 July 2024 1,607 1 View

Are you looking for research collaboration ?

we have few papers ready for submission, and we need one co-author for each article who can pay article fee. Interested authors may text here or contact me on my following email id [email protected]

29 July 2024 6,626 0 View

Dear researchers. pl help how to plot jablonski energy level graph and magnetic hysteresis curve in origin?

through origin software

17 July 2024 4,991 0 View

Getting this error : gmx_mpi': corrupted size vs. prev_size: 0x0000000001d1b320 ***?

i am using the trjconv command in gromacs gmx_mpi -debug trjconv -s md.gro -f md.xtc -o utr.xtc -fit rot+trans and after few steps i got the error gmx_mpi': corrupted size vs. prev_size:...

17 July 2024 6,216 1 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Any suggestions to enhance the wettability and adhesion of fluorosilanes?

I am facing a difficulty to prepare the thin film which contains fluorine contained silica monomer, as we know F is highly reactive with low surface energy and it could be the reason of low...

09 July 2024 6,017 3 View

How is artificial intelligence being utilized to enhance the diagnosis and treatment of sleep apnea?

AI has the potential to improve the management of sleep apnea by personalizing treatment, enhancing diagnostic accuracy, and advancing our understanding of the condition.

03 July 2024 9,393 2 View

Action research design is Quantitative Studies or Qualitative Studies?

Action research design is Quantitative Studies or Qualitative Studies?

14 June 2024 1,684 1 View

Offer or collaboration for book publications?

Dear Profs/ Scientist, if any one is interested or have plan to publish a good quality books/ book edited , I can contribute/help such type of research works . My research...

06 June 2024 5,932 2 View

How to draw SeDeM diagram for preformulation study of drug and excipients?

What is SeDeM expert tool? Is it in silico tool and how to draw the SeDeM diagram for preformulation study? Kindly suggest.

06 June 2024 4,408 0 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close