Please guide me , how can we design and program MFC actuators (d33 and d13) by using ANSYS ?

14 February 2022 1 3K Report

Claudio Pedrazzi

Thank you so much for your suggestion.I tried ANSYS help and found guidelines related to piezoelectric materials only . The available program does not work properly for MFC because MFC actuator has different configuration.

Badges
Science topic

Similar topics
Computer Science
Program

More Ali Raza's questions See All

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under op microscop?

How can we differentiate between calcite, dolomite, siderite, magnesite and ankerite minerals in carbonatite rocks in thin section under optical microscope?

07 August 2024 2,132 3 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

What is the best sampling strategy?

I am conducting a qualitative study that uses interviews to investigate the perceptions of teachers about a particular leadership practice and I am focusing on 3 schools which have a total number...

01 August 2024 8,457 10 View

Looking for help on sem image analysis?

Hello I am conducting a microstructural analysis of a soil treated with lime. The following sem images are of the untreated s1 and treated soil s3. The untreated soil contains quartz calcite...

01 August 2024 572 0 View

What is Random Audit?

HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...

31 July 2024 5,309 7 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Could it be a cell culture contamination?

Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...

09 August 2024 2,824 3 View

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

How to solve g_mmpbsa error?

Program: g_mmpbsa, version 2024.1 Source file: extrn_apbs.cxx (line 152) Fatal error: Failed to execute command: $APBS pybYcUWA.in --output-file=pybYcUW.out

07 August 2024 6,066 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Why activated CAR-Jurkat cell could not kill targets?

Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...

06 August 2024 641 2 View

How to isolate lymphocytes from mouse spleen?

I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...

04 August 2024 9,913 7 View

How to Add Missing Water Molecules in Protein-Membrane Simulations?

I have protein-membrane simulations (PDB, PSF, DCD) and have noticed that water molecules near the protein are not visible in the simulations. How can I fix this issue? Is there a way to place the...

04 August 2024 1,200 2 View

Does long-term culture of murine Monocytes result in macrophage differentiation?

Hi, I am isolating monocytes from the bone marrow using the Mouse Monocyte EasySep kit. I want to treat these cells and monitor expression of specific markers over the course of 10 days. I will...

04 August 2024 7,282 2 View