Oxidation level of machining chip?

More Daniel Martinez Krahmer's questions See All

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

H-index issues?

Hi Sir/Madam, I would like to know why my h-index is stuck to 15 despite the number of new publications added. Could you explain me how marks are granted. Best, Daniel

28 July 2024 2,607 2 View

I'm looking for a tool to evaluate the risk of bias in... Are there any recommended applications or platforms?

Dear researchers, In a systematic review (not a meta-analysis) compiling studies on various diagnostic systems against a specific pathogen. The most relevant parameters evaluated are the type of...

03 July 2024 9,069 3 View

What is the current usage and patronage of parks and greenspaces by older adults (aged 65+) in Salford? How does the frequency of older adults' visit?

What is the current usage and patronage of parks and greenspaces by older adults (aged 65+) in Salford? How does the frequency of older adults' visits to parks and greenspaces in Salford relate to...

22 June 2024 7,616 1 View

How can we compare SENTINEL vs LANDSAT for NDVI?

A question to see who can answer it. If the red and infrared bands of the satellites are...

16 June 2024 2,249 1 View

ImageJ Concentric Circles?

Hi there! We are trying to use the Concentric Circles Plugin on ImageJ to determine signal intensity in neurosphere cryosections after immunocytochemistry/confocal analysis. We determined the...

12 June 2024 7,332 0 View

How do i use researchgate to cunduct literature review ?

I am a first-time researcher in the field of nursing and i would like to conduct research about knowledge and attitude towards prevention and spread of tuberculosis.

11 June 2024 3,821 2 View

Is there any possibility for cultured mouse neurons more than 7 days?

Dear colleagues, I'm planning to start neuron mouse co-culture with astrocyte and microglia but I heard that it's difficult to keep it up. Any advices?

27 May 2024 4,905 3 View

What are some possible technical failures during lentiviral packaging using HEK293T?

I'm having trouble packaging lentivirus in HEK293T using pCMV, pMDG, an shRNA and polyfect. I normally seed 1.5 x 106 HEK293T cells in 60 mm on Day 0, which translates to about 60 to 70%...

20 May 2024 9,067 1 View

What is the minimum amount of liquid and beads I can use for bead-beating in a 2ml vial?

I am planning to extract DNA with QIAamp Mini DNA extraction kit (Qiagen) from DNA Shield microbiome preserved samples. My samples contain small amount of cell, so my goal is to reduce the loss of...

14 May 2024 2,291 2 View

Availability of laser assisted machining (turning) in India?

Sir, I want to work on the laser assisted machining (turning) of Nickel Based Super alloy. Please help in finding the laser assisted machining facility in India. Thanks and regards

02 July 2024 2,086 2 View

What does an increase in intensity mean in GIXRD?

When I examined the GIXRD data obtained recently, I observed that the sample treated with O2 plasma on the Cu surface deposited on Si chips showed increased intensity compared to the sample...

19 June 2024 6,900 5 View

When simulating the turning process in Abaqus, I cannot see chip formation in the results. What should I do?

Hi everyone, I am a beginner in ABAQUS and have modeled a turning operation using dynamic explicit. The results are kinda meaningful but it does not display the chip formation at all. 1-The...

14 June 2024 2,100 2 View

How to remove the oxide formed on the Ti6Al4V due to the temperature rise by wire EDM without using polishing?

Hello everyone, I need assistance to remove the oxide formed on the Ti6Al4V. During the cutting by wire EDM, oxide was formed on the surface of the alloy. Since the micron level features are...

22 May 2024 5,871 4 View

How to dissolve Span 80 in mineral oil or liquid paraffin?

I want to work on microfluidic chip. Dispersed phase of alginate solution and continuous phase of Span 80 solution in combination with mineral oil or liquid paraffin. But I had a problem with the...

19 May 2024 1,790 7 View

Is it possible to link Taqman probes onto solid surfaces?

I've been doing qPCRs a lot recently. I just wonder if we could link the qPCR probes we use onto surfaces so that we could creates some sort of chips. If not, is it also possible to link just the...

12 May 2024 5,397 0 View

Do we have to check the efficiency of sonication by doing a gel run everytime before proceeding for ChIP?

I am trying to optimize ChIP for my cell lines. I am doing with WT cells. I keep checking sonication efficiency on an agarose gel. So if I take a new sample of the same cell line, do I have to do...

06 May 2024 7,321 0 View

How we can use WASPAS, CRITIC, & COPRAS approaches are utilized to optimize machining settings as well as test material properties? Give some example?

Please some examples for WASPAS,CRITIC ,COPRAS in optimizing machining parameters!

01 May 2024 6,614 0 View

Can WASPAS, CRITIC, and COPRAS approaches be utilized to optimize machining settings as well as test material properties?

OPTIMIZATION

28 April 2024 9,186 1 View

What are these black spots on the machined surface?

I have done micro milling and these dark spots are visible in both conventional micro milling and ultrasonic vibration assisted micro milling. What can be these possible spots on the machined...

20 April 2024 6,644 0 View

Haydar Al-Ethari

Please explain your question. Which material? which type of machining? during the machining process or after? What do you mean by the oxidation level exactly? If you mean the oxidation of the chip you can make test related to the compositions of the chips (chemical composition, XRD,.........) ........ Good luck

Daniel Martinez Krahmer

The material is a carbon steel with 0,4%C. The machining is turning and we need to measure the oxidation level of chip after the machining.

Oxidation level is the quantity of oxigen have the chip after the machining process.