Numerical simulation of orthogonal turning using SPH in ABAQUS?

11 August 2018 0 1K Report

I am doing numerical simulation of orthogonal turning using SPH particles in ABAQUS. I could modelled it, but after completed the simulation the workpiece is translated and rotated. In the boundary condition, I had fixed or encastered left side and bottom of the workpiece by creating a set of nodes.

Anyone having idea on how to give the boundary condition to SPH particles, please help me.

Badges
Science topic

Similar topics
Indexes

More Sumesh c s's questions See All

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

Which is the best software or programming language (user friendly) for analysing data?

I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...

20 February 2021 3,950 15 View

Hi..how to isolate crude HDL (all subfractions) from human serum by size exclusion chromatography?

I would like to know about isolation of crude HDL from serum by SEC. Is it possible to perform with a serum sample volume of

19 February 2021 5,576 2 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View

Do you have any experience with transfection of EBV immortalized B cells with Lipofectamine?

I know that efficiency of transfection for primary B cells is very low with Lipofectamine. But I did not try that for EBV immortalized B cells. Do you have any experience with transfection of EBV...

05 February 2021 4,159 1 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to find a correlation between coordinates in a curvilinear coordinate system?

Hello. I have a skewed elliptical coordinate system (I use alternative elliptical coordinates). And I need to determine connections between coordinates in order to fetch a covariance matrix of...

28 February 2021 364 3 View

How long does it take to get a modeller(for homology modelling) license?

I submitted my e-mail address on modeller website to get a license. The problem is that, the site cannot process my school e-mail (ewhain.net). I submitted my Lab website and school name so that...

25 February 2021 9,054 3 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Why does the sum of reaction forces not match the force component of a Free Body Cut in Abaqus?

I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...

23 February 2021 711 3 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View