Modling and simulation of microfludic based amperometric detection?

05 May 2018 0 10K Report

Can anyone tell me any software which can be used for modelling and simulation of microfludics based amperometric sensor?

Badges
Science topic

Similar topics
Methodology
Sensors

More Rishi Raj Raj's questions See All

Cyclic Voltammetry of commercial gold electrode in 50mM H2So4?

i am a beginner in cyclic voltammetry and I have tried with 50mM of sulfuric acid. I got this curve(attached). can any one please tell me I am in the right direction? If it is correct please...

05 June 2018 4,537 1 View

I have synthesis polyaniline CSA doped by interfacial polymerization but it shows blue colour in DMF solvent why? It should show green in acidic media

Synthesis people will help me.

06 July 2017 6,561 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,600 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View