Modelling of inorganic nanostructures?

More Zahra Shakeran's questions See All

What is the Methotrexate solvent?

Hi , What is the methotrexate solvent. I try to use methanol, DMSO and DMF. But methotrexate was disolve very slightly in these solvent. Methotrexate is a hydrophobic anticancer drug. I can not...

09 October 2018 6,528 11 View

How can I doing release test for very little amount of drug-nanoparticle?

Hello everyone, how can I doing release test for very little amount of drug-nanoparticle? for example for 500 micro-gram drug, loaded in 500 micro-gram nanoparticle. can I using dialysis...

07 August 2018 5,297 0 View

Temperature-sensitive nanoparticles sterilization?

Hello How can sterilized silica nanoparticles, which have been modified by temperature-sensitive polymers? Thank you.

05 June 2018 6,256 1 View

Amber or Gromacs?

Hi, Does anyone know which system is better for molecular dynamic simulation? Amber or Gromacs? Please mention your reason? Thank you so much.

03 April 2018 8,957 7 View

Simulation of Mesoporous Silica nanoparticle?

Hi, I want to simulate Mesoporous Silica nanoparticles to using them in molecular dynamics. Has anyone been working on the simulation of these nanoparticles? Thanks.

02 March 2018 7,085 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

I need JCPDS file of LSFCO nanomaterial. Can anyone provide me?

Require for Rietveld refinement in XRD.

08 August 2024 3,081 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Mustafa Dinç

Hi Zahra,

You may try to use Anylogic or NetLogo, which is open source, simulation tools.

Rakesh Sonker

The theoretical and computational simulation of

inorganic nanostructures, nanoparticle for different classes of inorganic substances use the gaussian 09 software free download. These simulations are related to their synthesis and experimental studies. A theoretical formalism is developed to describe 1D nanostructures with symmetric shapes and inorganic nanostructures.