I have driven piles designed for a building but the piles are not the common bored piles? can I use the Embedded beam row?
I feel it is better to use pile volume element instead of embedded bean element to simulate the pile..embedded beam is a structural element and need to assign limiting skin friction and tip resistance in the analysis.
Dear Researchers, As shown in the figure there are two strip footing, the short one that has already been constructed and the long one for the same structure. The question is, Is there some...
31 December 2018 1,981 3 View
Where can I obtain typical train moving loads to conduct an analysis in Plaxis 2D 2018.? The load is applied as a dynamic input right? Thank you.
10 November 2018 5,128 3 View
The weak soil properties has a shear wave velocity less than/equal to 300 m/s and low SPT N values among other characteristics of soils. How will you determine the properties of the treated soil...
06 July 2018 5,019 2 View
While doing liquefaction analysis, what is the correct water boundaries during the analysis? -seepage -outflow?
02 March 2018 4,302 9 View
Dear Researchers, I want to model a pile and perform Non-linear analysis in Sap2000. My idea is giving the pile a certain displacement from an earthquake data and analysing the pile in...
01 February 2018 6,332 4 View
I want to use the FLAC program to analize an existing bored pile example. I want to study it for a month to come to a capacity of modelling a bored pile with pre stressed anchors. Any assistance...
31 December 2017 7,141 6 View
I want to acquire an earthquake data of M=7.5 and a=0.4g but I do not know exactly how to input the parameters in the peer ground motion database so that I can get the data with the given...
11 December 2017 8,832 2 View
In plaxis when doing dynamic analysis or liquefaction it is advised to do analysis in 1. Ko , initial phase 2. phase 1 with DIFFERENT SOIL characteristics and Phase 3 the dynamaic analysis with...
11 December 2017 1,839 4 View
Hey guys, I want to do a dynamic analysis of a building in plaxis. I have questions as follows; 1. Which soil model to use?Mohr-coulomb or hardening soil model?or HsSmall? 2-a. I can enter the...
11 December 2017 9,569 2 View
I am doing a liquefaction analysis in plaxis and I am always getting the Ru value as zero? What could be the reason?
11 December 2017 7,166 4 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...
31 July 2024 9,733 3 View