Micro heater for PVD?

04 April 2016 0 8K Report

From where can I procure micor-heaters? Planning to design a small PVD setup. What are finer points I should consider. A 1 stage Vacuum pump/rotary is sufficient or I need a better setup for a simple system?

Badges
Science topic

Similar topics
Heat

More Sandip Pchoudhury's questions See All

Change of intensity with doping?

Dear Researchers, I have my samples SnO2 doped with with Cu (1, 2, & 4%). The peak intensity reduces in XRD for 1 and 2%. However, for 4% additional peaks appears which I believe is due to...

05 June 2019 4,806 3 View

CNT-metal oxide combo?

Dear Researchers, Since CNT is not soluble in standard solvents like DI water, ethanol etc, how do I make a doping/composite of CNT and metal oxide. Your suggestions will be highly appreciated....

05 June 2019 6,386 2 View

How to measure the amount of sample (quantum dots) in a solvent?

I have quantum dots dispersed a solvent. If I am considering 2 ml of the solvent, then how do I find out how much is the amount of sample in that solvent? I tried drying the sample to obtain...

03 April 2019 4,333 8 View

Which solvent to dissolve Co3O4 and NiO?

Some literature and RG search mentions a acid solution for dissolving Co3O4 and NiO. Also, for Co3O4 I tried a basic medium of pH 10, but was unable to dissolve. I am not sure incase I am using...

10 November 2018 4,297 0 View

SAED Image analysis?

Dear Sir/Mam, Considering the scale, we measure the distance between the centre and the bright spot of the diffraction pattern. This should tally with the reciprocal of the d-spacing and the...

07 August 2018 3,371 2 View

High temperature hydrothermal reactor?

Kindly let me know the details along with an image of a high temperature hydrothermal reactor operating at 400c to 500c. Thanks and regards

06 July 2018 5,765 3 View

Measurement of Size of Quantum dots?

Dear Sir/Mam, I have synthesized some quantum dots suspended in solvent (DI water) . I am interested in finding the size of those dots. One way would be offcourse HRTEM. But I am interested in...

05 June 2018 8,740 3 View

Synthesis of Graphene Oxide - not by Hummers method?

I am interested in synthesizing Graphene Oxide but not by Hummers method. If any one can suggest from his/her expertise. Also, does other method or even Hummer method ensure a good quality. Also...

05 June 2018 2,962 0 View

Screen printers and gas sensing setup?

Dear Sir/Mam/Colleague, What kind of Screen Printers do I use to deposit thin films? If possible provide me with a link of the description of the instrument. Also, what will be the approximate...

09 October 2017 9,136 0 View

Writing a project?

I worked on metal oxides and its application for gas sensors. Now I intend to write a project, and found Bio-sensors (using metal oxide) as a very interesting project. My doubt lies, whether the...

07 August 2017 5,478 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to separate water from glycerol solvent in a solvent recovery vacuum distillation column?

I am currently doing my third year design project. I have been assigned to design a glycerol recovery column in vinyl acetate monomer production. The process unit before the recovery column is an...

01 March 2021 9,525 4 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View