Dear All
I already prepared N doped TiO2 using sol gel technique. Please, may anyone provide with a preparation method to incorporate graphene with a solid catalyst of N doped TiO2?
Regards,
Dear Amal
Hydrothermal synthesis should work for it. For detailed information, you can read the following papers:
http://pubs.rsc.org/en/content/articlelanding/2011/jm/c0jm03542d#!divAbstract
http://link.springer.com/article/10.1007/s12274-011-0136-7
Hope this helps!
Dear Monisha
Thanks for your favorable reply. Is that method work the same with N doped TiO2 as TiO2?
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?
04 August 2024 1,078 1 View
If the pairs are similar, will it reduce the adhesion due to electric charges?
29 July 2024 3,185 2 View
I've been trying to design primers for qPCR to detect NCF1 cDNA using Primer3Plus and NCBI Primer-BLAST, but I couldn't find primers that are specific to the gene. Any help ? Thanks !
04 July 2024 3,068 3 View
I am trying to understand the influence of polymer films sliding against each other. For the simulation, I saw many molecular dynamics simulations, like LAMMPS, GROMACS, etc. I am new to this...
09 April 2024 8,871 2 View
I have been trying for months to grow kidney cells from rat kidneys, I tried several methods, serial sieving, cutting and meshing, and using kidney tissue to obtain an outgrowth of cells. I always...
11 March 2024 2,665 1 View
if I have 5 grams of PMMA, how much (mL) of Chloroform should I used to dissolve it ? should U use sealed beaker to this process?
25 February 2024 9,066 0 View
Hello, Does anyone have any idea of the exact (if any) number of cells we can have in mosquito salivary glands (the species doesnt matter at this stage). Thank you
05 February 2024 823 0 View
Hi how can I upload a manuscript for a paper that wasn't uploaded before thanks?
21 December 2023 7,777 0 View
Hi, I will be culturing BM-MSCs in DMEM culture media, based on the literature, I will add 10% FBS and pen/strep... except when I checked the one that we have, I found that we only have...
10 December 2023 6,681 3 View
I need to do some experiment with it in liquid form.
07 August 2024 613 3 View
Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...
06 August 2024 8,716 0 View
I have been working on Red blood cell-derived extracellular vesicles as Antisense Oligonucleotide (ASO) carriers. We normally run agarose gel to quantify the loading efficiency. I used naked ASO...
06 August 2024 3,130 2 View
I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.
02 August 2024 6,789 4 View
I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...
01 August 2024 8,368 2 View
It's an end-point PCR protocol. I'm using 1.5% agarose gel with SyBR Safe dye and TBE as a running buffer, visualization on BioRad XR+ system. I was primarily thinking of primer efficiency,...
01 August 2024 4,673 4 View
The starting material is a finely ground powder. Some particles contain more graphene than others.
30 July 2024 3,978 2 View
Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...
30 July 2024 3,849 0 View
Greetings. I’m currently running a nested pcr for giardia. My mastermix comprised of 3mM Mgcl2, 5unit of taq polymerase, 0.2uM of forward and reverse primers each respectively and 0.2mM of dNtp...
22 July 2024 9,761 5 View
Hello everyone, I am running DFT with CP2K software at 1200 K, 1 bar with a periodic system of 64 Al atoms + 2 CO2 atoms. However, I am seeing my temperature slowly increase to >4000 K and my...
22 July 2024 3,177 0 View