How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Performing a nonlinear analysis on masonry building subjected to tunnelling?

I am trying to model a masonry building over a steel beam to simulate the soil settlement profile, when the model is completed the analysis does not converge effectively (for a total of 11mm a the...

27 October 2020 5,034 1 View

How can I apply Cyclic loading in ANSYS Mechanical APDL as a second Load step after a Static 1st Load step?

I am simulating a masonry wall under in-plane cyclic loading. Before the cyclic load is applied, it must be loaded with gravity direction surcharge load (or pre-compression). However, whenever I...

14 October 2020 3,253 1 View

Can anyone share a UMAT subroutine for Concrete Damage Plasticity model (CDPM) ?

Please share any Example, Tutorial or any article related to CDPM. For a 3D Pushover analysis. >> [email protected] Thanking in anticipation!

16 August 2020 3,996 8 View

How to modelling the concrete rigid slabs in a masonry building ?

I am working on developing an accurate 3D model. When I defined the rigid slab the analyses aborted for the static step. In the Message file appeared this: ***NOTE: THE SOLUTION APPEARS TO BE...

22 July 2020 3,431 2 View

Masonry wall modeling issue (ABAQUS) - Is this related with material or constraint ?

Dear Abaqus users, I perform a static analysis with a Standard module on a masonry wall macro model. Four surfaces interact with a reference point in the middle of the model as in the photo...

14 July 2020 4,560 2 View

How to define Tensile and Shear Strength of SOLID65 in ANSYS Mechanical APDL?

I am modeling a brick masonry wall in ANSYS. The adjacent bricks (SOLID65 elements) are "joined" by surface to surface contact elements with certain normal and opening stiffness. I defined...

14 April 2020 6,795 1 View

What is a good way (finite element software) to simulate mortar properties between masonry, such as how to model more effective?

What is a good way (finite element software) to simulate mortar properties between masonry, such as how to model more effective?

09 April 2020 2,381 3 View

How to control initial stiffness of global base shear vs lateral diplacement response in masonry infilled RC frame in ANSYS APDL?

Hello everyone I am modelling masonry infilled RC frame in ANSYS Mechanical APDL and defining joints (between mortar-mortar, infill and RC member) using cohesive zone material model. But the...

11 March 2020 6,403 4 View

How to apply cyclic loading to a discrete model of a masonry wall in 3DEC software?

It is possible to apply a monotonic load to a URM wall in 3DEC code but I am wondering is it possible to apply a cyclic load there like FEM softwares?

10 February 2020 3,237 3 View