Kindly give me comment/idea on the following Swat Moddeling results: p-0.38 r: 0.18 R2: 50, NS 41. I have tried alot to reach this far. is this Good?

01 January 2018 0 649 Report

SEDIMENT SIMULATED USING SWAT

CALIBRATION, ETC. SWATCUP

SUBBASIN; UNGAGAUGED, BUT MAIN BASIN HAS A GAUGE ABOUT 13

FRUSTRATING OBSERVATION ON SIMULATION: SIMULATED VALUES COMPARED TO MEASURED MISSED DATES IN SELECTED INSTANCES, E.G. IF OBSERVED SEDIMENT LOAD OF 1.3 tone per day is recorded on 12th January corresponding simulated will occur either 10 or 11th or 13 or 14th. THE VALUE WOULD BE FAIRLY CLOSER TO OBSERVED, BUT ON A DIFFERENT DAY. I ENDED UP HAVING STANDARD DEVIATIONS, MEANS FOR OBSERVED CLOSER TO EACH OTHER BUT, POOR P, R, R2 AND NS VALUE.

Badges
Science topic

More Manoah Muchanga's questions See All

Which p and r value should i consider between those from the default SWATCUP simulation and those from the Behavioral parameter simulation?

What does behavioral simulation mean? should i adopt its summary statistics if it has better statistics than the standard/default summary statistics? see attached image of my summary simulation...

02 March 2018 2,222 0 View

I hav a 1time measurement of sediment in a reservor (172632.6 ton.). How can I estimate daily loads based on this cumulative total from 1988 to 2013?

Computing daily sediment load based on a one time cumulative measurement. I have some discharge data but no sediment except the one I measured.

09 October 2017 5,884 10 View

Run swat error?

I WAS TRYING TO RUN MY SWAT MODEL, BUT IT IS GIVING ME ERROR: forrtl: error : floating invalid. I have attached a screen shot of an error. can someone please assist how i can resolve...

08 September 2017 7,054 5 View

I am currently preparing input data to run SWAT, I am looking for an Excel template with USLE equation to easy my work. If you have one help please.

SWAT GIS

07 August 2017 4,282 0 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

Uncertianiny in using dry or wet basis in mixing a sediment with fuel oil?

Hello I'm currently working on a topic related to studying the anaerobic biodegradation of TPH in marine sediments. In this work, sediment should be mixed with fuel oil to a concentration of 20 g...

24 February 2021 9,839 3 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

Is it okay to mention you distributed your qualitrics study link through social media sites?

Just want to be clear and know it is okay to say I have distributed the qualitrics link through social media such as Facebook, Instagram and Twitter to ensure my target audience is reached in my...

21 February 2021 5,143 2 View