03 March 2018 0 2K Report

What does behavioral simulation mean? should i adopt its summary statistics if it has better statistics than the standard/default summary statistics? see attached image of my summary simulation statistics.

More Manoah Muchanga's questions See All
Kindly give me comment/idea on the following Swat Moddeling results: p-0.38 r: 0.18 R2: 50, NS 41. I have tried alot to reach this far. is this Good?

SEDIMENT SIMULATED USING SWAT CALIBRATION, ETC. SWATCUP SUBBASIN; UNGAGAUGED, BUT MAIN BASIN HAS A GAUGE ABOUT 13 FRUSTRATING OBSERVATION ON SIMULATION: SIMULATED VALUES COMPARED TO MEASURED...

31 December 2017 685 0 View

I hav a 1time measurement of sediment in a reservor (172632.6 ton.). How can I estimate daily loads based on this cumulative total from 1988 to 2013?

Computing daily sediment load based on a one time cumulative measurement. I have some discharge data but no sediment except the one I measured.

09 October 2017 6,084 10 View

Run swat error?

I WAS TRYING TO RUN MY SWAT MODEL, BUT IT IS GIVING ME ERROR: forrtl: error : floating invalid. I have attached a screen shot of an error. can someone please assist how i can resolve...

08 September 2017 7,207 5 View

I am currently preparing input data to run SWAT, I am looking for an Excel template with USLE equation to easy my work. If you have one help please.

SWAT GIS

07 August 2017 4,481 0 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close