Joint impedance and muscle stress/strain models in Matlab Simulink?

12 December 2017 0 10K Report

Where can I find joint impedance and muscle stress/strain models modelled in Matlab Simulink for human leg?

Badges
Science topic

More Mohd Razali Sapiee's questions See All

How can I have the data sampled as 101 data points from 0% to 100%?

I have kinematics data based on gait index which defines gait cycle based on 0-1000 gait index. One cycle consists about 546 data (not quite exact as due to sampling, data for new cycle might...

04 May 2019 9,702 4 View

Where can I get normal and abnormal walking gait data?

I need walking gait data for normal walking gait and abnormal walking gait (any conditions). Where can I get those data in excel form and validated or supported with publications? I intend to...

10 November 2017 8,324 0 View

How to design controller for lower limb exoskeleton by using matlab?

I want to design a controller for lower limb exoskeleton robot by using matlab, where should I start? Do I need to model the lower limb first or just use any available models as tools and then...

01 February 2017 1,681 3 View

How can I simulate human lower body and exsokeleton from suitable CAD software with Matlab simulink control?

I have articulated human body CAD model and I want to control the model lower body by using gait trajectory data in simulink. How can I simulate the model from simulink and at the same time I can...

02 March 2016 4,605 3 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

Swimming/space travel depends on the proprioceptive muscle spindles?

When the entire neocortex is ablated in rodents, although they are still able to swim, all the limbs move continuously and asynchronously (Vanderwolf 2006; Vanderwolf et al. 1978). Normal animals...

03 August 2024 835 3 View

Expansion thermal of muscle ?

What is the thermal expansion coefficient of human muscle?

27 July 2024 7,190 0 View

For anyone that works with Human Aortic Smooth Muscle Cells(HASMCs), what seeding density do you use when plating?

I am struggling to find a seeding density that will allow my cells to not aggregate together. Anything helps!

24 July 2024 3,460 1 View

Element deletion problem in ABAQUS/Explicit solver using Cohesive elements?

I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...

23 July 2024 10,032 0 View

I ask Chinese seismologists to inform me: who should I contact to create a joint Forecast Center?

I ask Chinese seismologists to inform me: who should I contact to create a joint Forecast Center? I do not hide that the beginning of my work was connected with the successful forecast of the...

22 July 2024 2,276 1 View

Does anyone have sources where I can find the contraction ratios (% shortening of muscle length during full contraction) of specific muscles?

I founde some textbooks stating that typical skeletal muscles can shorten up to 70% (optimally up to 30%) during contraction. However, I would like to look at muscles per region. This might seem...

21 July 2024 399 3 View

Does EMG show muscle spasms?

Electromyography waveforms reflect the electrical activity of a muscle. But does it reveal muscle spasms (transient) or cramps (prolonged spasm)? If so, what does it look like?

20 July 2024 5,951 1 View

How to simulate a varying three-phase load /load profile in Simulink/MATLAB?

I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...

14 July 2024 8,892 3 View

Why my mesh independent fastener as beam cartesian type not working in abaqus?

i have attached my model and i have used point based mesh independent fastener using attachment points and type of connector is basic cartesian but this is not working as i apply displacement on...

02 July 2024 6,293 0 View