I'm doing the simulation of pulsating heat pipe in ansys fluent, when I use phase change UDF , mass source is not showing in cell zone condition why?

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

What are the harmful effects of these extreme rainfall on the health of newborns? What are the reasons for that?

Extreme rainfall associated with climate change is causing harm to babies in some of the most forgotten places.

01 March 2021 5,647 4 View

Ram Kumar Pal

Dear friends, sorry for replying too late, I was busy in PhD entrance test. In udf the term DS[eqn] is used to linearization of source term which ultimately help and improve in the convergence of solution. To know more about this term see "Source term linearization" in any CFD book.

Dear Haghani, the udf that is attached here in this thread is not correct. I have made some correction in this udf. Currently I'm busy in my project work. I'll contact to you for details via email that is written above by you.

thanks

Avinash Kumar

Mr Ram Kumar Pal,

I am doing my final year project on heat pipes . I need to make simulation of a heat pipe . I am not able to simulate the condensor region properly , I refered many research articles in this respect , it was mentioned I need to use a udf code for it. Can u kindly share ur corrected udf code . It would be of great help . Thanks in advance

my email id : [email protected]