i am modeling steel angle bolted connection , when plot stress strain curve for an element in the top angle(red one) , the curve far away from input data (blue one)
can anyone explain please
How far is this element from your boundary condition? it is close to an opening or edge? Also what stress are you reporting? von Mises?
i am working on bolted angle steel connection , how to model the symmetric for bolts with beam web , and how to apply pretension force for these bolts since it will model as half bolt and the...
09 October 2018 7,321 3 View
moment curvature curve from many models in abaqus for bolted angle steel connection gives always higher values than experiments , i tried to generate many models but always getting same results...
08 September 2018 7,552 1 View
How will i represent the bolt in shear IN ABAQUS (i have gross area and stress area ) , i read some paper talk about make a void inside the bolt . any suggestion
08 September 2018 3,860 0 View
I am working on steel bolted angles connection, my issue is when I mesh the flange thickness of the beam and column I got a very different curve from same model when the flange thickness not meshed
08 September 2018 1,305 2 View
I am modelling Steel connection and i I apply foce on the beam to make moment on the connection. But when I increase the applied load, the displacements and stresses are always increasing. In...
07 August 2018 4,928 0 View
I am modelling Steel connection and i I apply foce on the beam to make moment on the connection. But when I increase the applied load, the displacements are always increasing. In other words, the...
07 August 2018 1,447 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,141 3 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View