Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

Analysis of CRD two factor using R studio ?

Hello everyone. I have conducted the research on post harvest longevity of tomato crop using plastic packaging and different doses of chemicals as two different factors. The design of experiment I...

28 February 2021 8,189 3 View

What is the exact mechanism of the antimicrobial effect of local anesthetics?

The antimicrobial effect of local anesthetics has been known for more than 50 years, but it still seems to have an unclear mechanism of action. which bacteria? which concentration? etc etc. ....

27 February 2021 4,450 2 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View

What are your alternative data collection methods during the pandemic? What are the pros and cons?

Dear colleagues We are exploring possible data collection methods for environment and behavior research in the context of architectural environments. Have you conducted any Post Occupancy...

16 February 2021 2,575 4 View

Can bio-decomposer be a successful alternative to reduce residue burning?

To maintain the proper crop plan most of the times there is not enough time to make the field ready for the next crop. In this particular context , can bio-decompser be a solution? What about...

16 February 2021 7,068 24 View

Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

ZnS oxidizes to ZnO!!why??

when I put my ZnS solution in the chemical bath, the ZnS oxidizes so there are ZnO peaks appearing because of the reaction with the oxygen in the air, despite the fact that I close the beaker...

14 February 2021 5,778 9 View

Charmm/GROMACS Residue 'ZN' not found in residue topology database?

I am trying to do some MD simulations of a protein with zinc ions. I am trying to use a charmm forcefield (I have tried 2017 and 2021) and Gromacs. I get an error when doing pdb2gmx Residue 'ZN'...

12 February 2021 9,367 2 View

What is the difference between Graphene Oxide and Expanded Graphite?

What are the main differences between Graphene Oxide and Expanded graphite, in terms of surface functionalities, conductivity, d-spacing and other features? Is the term expanded graphite...

06 February 2021 9,810 4 View

PEG coated Fe3O4 nanoparticles in aqueous NH3?

Hello, I synthesized PEG coated Fe3O4 nanoparticles by coprecipitation methods and I would like to ask whether they can be dispersed in aqueous NH3 since they have a PEG coating and theoretically...

06 February 2021 5,217 4 View

Xrd result of ZnO thin film shown better crystallinity at low temperature and the crystallinity decreases as the temperature increased. why?

I have synthesized ZnO thin films at four different substrate temperature say, 300, 350, 400 and 450C. and the samples were annealed at 450C for half an hour. the xrd result shown better...

04 February 2021 7,641 4 View

How to apply graphene oxide on an gold electrode?

Dear Fellows, now it is the time to push graphene applications further in terms of easy and low cost production surroundings. Thus I recently dived in the materia and I am facing tons of papers,...

02 February 2021 6,284 2 View