07 October 2015 5 2K Report

Hi there,

my research concentrates on standardized processes in manual labour. Foremost I want to define standardized work in a more specific way.

Once I'm done with it I want to find out, if certain standard levels are connected to characterized levels of physical and psychological stress.

Therefore I need some guideance to find relevant papers, which connect standardized work in gerneral with physical or psychological stress.

I would be very grateful for any kind of help.

Best regards

Lukas

More Lukas Bier's questions See All
Are there lab markers/pens resistant to Roti-Histol?

Hi, I'm looking for a pen/marker to write on the smooth, transparent (non-frosted) part of microscopy slides which does not get washed away by alcohols and most importantly Roti-Histol. I want to...

24 February 2021 9,902 5 View

Avoiding pseudo-replication - Calculate replication means or formulate a crazy model?

Hi! I assessed a phenotype on 8 different plant genotypes in 4 real, independent, biological replicates. A priori, half of the genotypes is "classified" as resistant (R), the other half as...

17 May 2020 165 6 View

What is the best grammar check application?

We, scholars, are writing a lot. The language of science today is the English, however, for many of us, English is not our mother tongue. Even though we may be fluent in English. I found grammar...

23 February 2020 3,696 36 View

Do you know any Papers about Backflush on Demand (BoD) or Predilution on Demand (PoD) in Hemodialysis?

I am currently working on my Thesis about the maximization of the delivered hemodialysis Dose and stumbled about the BoD and PoD techniques mentioned in "Hemodiafiltration: Technical and Clinical...

13 February 2020 8,832 3 View

Why does my EPOC+ Raw data have a lot of spikes ?

I'm working on a little project to measure Emotions with different Methods (K-NN, DNN, NN, Random Forest ...) At the moment I have two data sets, with one of them I train the different methods...

05 February 2020 7,833 2 View

What's the best way to increase adhesion of silver nanoparticles on TiO2?

Nanoparticles are fabricated on a TiO2 layer via an EBL process with subsequent metal evaporation and lift off.

25 September 2019 9,616 5 View

Analyzing Likert Scales - What to use????

Hello everyone, I want to analyze several Likert Scales ranging from 1 Strongly Disagree to 7 Strongly Agree using SPSS. I have a total of 6 Likert Scales, which I put together out of 5 Likert...

05 May 2019 3,143 6 View

Which Diversity Index should be used when comparing forest stands regarding their resilience to droughts?

Hello, I am investigating the response of single trees and whole stands to droughts by calculating resistance and resilience indices using the Basal Area Increment of the trees. I want to figure...

08 April 2019 5,029 4 View

How can you transform TOA Reflectance to BOA Reflectance?

Hello, My aim is to have a Landsat image - BOA reflectance with relative values (0-1) so with floating point. Through the Envi software I am able to get BOA (surface) reflectance but without...

16 January 2019 4,397 3 View

What is the favourite CFD meshing tool of your choice?

Which meshing tool are you using for your CFD calculation? Which CFD Programm are you using?

13 November 2018 9,663 23 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close