Is there anyway to make SAS unfriendly and not-publication ready output a little bit friendly?

More Faramarz Sayyedi's questions See All

Does anyone know by any chance how we can delete the extra rows in Mean Comparison Output of SAS? and make a publication-ready ANOVA table?

Unfortunately, SAS output is not that user-friendly and publication-ready, it is a very powerful software, though.When I perform ANOVA using PROC ANOVA or PROC GLM and add MEANS, the output ANOVA...

03 September 2016 5,138 4 View

Where is it possible to buy a polarizer device for a FT Raman spectrophotometer equipped wit Nd:Yag lazer source?

We need a polarizer devise to measure the depolarization ratio.

07 February 2016 686 4 View

How can I stop distortion?

HiI try to simulate a metal forming process with abaqus/explicit.I use of mass scaling method with 1E8 factor. During of solution the kinematic energy is less than 10% of total energy. Because of...

25 November 2014 3,527 6 View

Does anybody knows about the role of K ion in resisting of plants against dryness?

K ion increases the resistance of plants in dry weathers.

25 May 2014 9,020 3 View

Can anyone help with AHP questionnaire results?

Having the questionnaire filled in I am not quite certain what I am supposed to do with them. I mean, let's say, I have offered the questionnaire to 30 people, how do you take average of their...

23 April 2014 8,034 10 View

How can I link mathematical software MATLAB to finite element analysis software ABAQUS?

The purpose of doing this work is to transfer the results of structural analysis of ABAQUS software to MATLAB software.

03 May 2013 4,822 10 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

How to manually calculate p value in ANOVA? what is the equation or formula for it?

03 March 2021 4,928 5 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Mixed ANOVA - help?

I'm currently working on a piece which asks to conduct an ANOVA - looking at the effect of sporting group (2 levels), and exercise trials (two trials with six levels). I've computed this all...

27 February 2021 9,626 4 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

How to Interpret Partial Eta Squared Numbers For a Repeated Measures Anova?

I have obtained Partial Eta Squared Numbers through Two-Way Mixed Anova Analysis. My results for different constructs are: .105, .135, .038, .068, .061 respectively. I wanted to know, whether...

24 February 2021 7,122 1 View

Can we proceed to perform Two-way Mixed-ANOVA despite normality violations?

While testing assumptions, Shapiro-Wilk Test failed. However, I proceeded with the analysis and the interaction effect was significant. During our course- lectures, it was mentioned that Anova...

24 February 2021 228 3 View

Sample size determination for non-parametric tests?

How do I run a a priori sample size determination for non-parametric tests, like the Mann-Whitney U-test and the Kruskall-Wallis or other non-parametric tests that accord with the unpaired t-test...

24 February 2021 166 6 View

Daniel Wright

If you are wanting to produce tables and figures and numeric output within either a word processed document or in html, I would look into using knitr. See http://yihui.name/knitr/. He does state that code could be written to use SAS instead of R, but I don't think anyone has done that.