11 November 2017 1 5K Report

I want to find the protective/ permissive turn type characteristics for SYNCHRO modeling for several intersections.

More Mohiuddin Imran's questions See All
What are the key differences among commonly used Travel Demand Forecasting software in Transportation Engineering?

What are the common software to forecast travel demand? Why do we choose one over another? What are the key differences? 

09 October 2017 7,763 5 View

What are some of the best ways to model ride sharing effectiveness for lightweight vehicles?

For most of the developing cities like Dhaka, there are a lot of NMVs, lightweight vehicles (CNGs, Auto Rickshaws) operational which are also contributing to the ridesharing purposes in several...

01 February 2016 4,930 2 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

• What the possible Persistent Organic Pollutants and Heavy metals present in fluorspar, sediments, and water bodies around its mining area?

Approximate concentrations are require in compared with the WHO permissible limts

11 August 2024 2,723 1 View

Does anyone know why this article is republished using the fake address. Is it about stealing my patent?

This article is mine. It was republished by unknown person using an address (Wilson N Jones Regional Center, Sherman Texas USA. I have a patent.

10 August 2024 7,528 5 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Is Galaxy.org good to use for research for analyzing data and for publication?

Hello all, I wanted to know, can I use galaxy (USA, Europe or Australia) platform for analyzing the shotgun data, and can it be used for publication purpose as well? Thanks :)

06 August 2024 6,610 4 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close