Is there any standard procedure to analyze biosensor stabilty over a period of time?

20 March 2024 1 8K Report

Most of the research articles mentioned biosensor stabilty study conducted for 21 days Or a month. Is it a standard period of time to test the working stabilty of a biosensor?

Hamed Zahraee

Hi Ajinkya Dabhade,

This test varies depending on the type of biosensor, and stability may differ in some biosensors due to low or high biological receptor stability. Therefore, performing stability tests at different times is necessary to determine the biosensor's detection capability and achieve maximum biosensor stability.

Badges
Science topic

More Ajinkya Dabhade's questions See All

How to find orthotropic material properties?

I am doing an impact analysis of bullet on a plate. But for that simulation, I require orthotropic properties of materials like PPS and PEEK which are Unidirectional type. How to find them?...

16 February 2021 8,775 2 View

Error While inserting Properties in ANSYS Data?

I want to do analysis in the ANSYS ACP module. For the same, I am trying to insert Properties of material in which I need to add Isotropic Elasticity ,orthotropic stress limit and Ply Type. But If...

30 January 2021 4,438 3 View

Is it possible to analyse the High velocity bullet impact on plate from 10 meter distance? In which software it ANSYS or ABAQUS or LSDYNA?

Hello all, Im Ajinkya. Doing analysis of High velocity bullet on plate made of 3 different materials from 10m distance. In which software it will be good for analysis ANSYS or LSDYNA or ABAQUS?

04 January 2021 9,462 4 View

Is there any FDA approved polymer or IIG listed polymer which is easily soluble in sesame or castor oil ?

I am in search of a polymer which has a solubility in oil.

25 December 2020 9,481 2 View

Reasons for hysys to crash while carrying out optimization using MATLAB ?

I am carrying out simulation based optimization by connecting MATLAB and Hysys using Activex. Hysyslib is used to connect hysys and MATLAB I am deploying genetic algorithm to carry out...

24 April 2020 1,899 3 View

Quantifying IHC between treatment groups?

I am looking for input on how to quantify the amount of signal from lung tissue sections stained with anti- alpha SM actin. Is there a program out there that I can upload images of my tissue and...

10 March 2020 4,044 3 View

How can I model a 2-D(axial and radial variation of variables) dynamic heterogeneous reactor model equations (PDE) ?

I have 2-D dynamic gas-solid reaction model, with variables( temperature, pressure, velocity) varying in radial and axial directions. The fluid and solid phase are not in equilibrium and momentum...

17 June 2019 416 1 View

How to verify whether MANT-GDP bound to Ras protein or not?

I am doing nucleotide exchange assay using Tecan spark 10 M machine.I have loaded KRas with MANT-GDP and used 1uM of the same and the relative Fluorescence units is around 32000. But the...

30 March 2019 5,852 4 View

How to prepare E.Coli cell lysate as I want to use it as negative control during SDS PAGE alongside my protein lysate ?

I tried using E.coli BL21 cells -grew them in 2TY media for about 2 hours ,centrifuged and lysed the cells using lysozyme and DNAse ? But i only got a single band at the bottom of my SDS Gel .

18 August 2017 6,260 3 View

What is a suitable solvent to dissolve diphenyl-diselenide?

Thanks in advance for your replies.

14 April 2015 2,572 5 View

Which period is considered as study period in research?

Is that starting from proposal development to result writeup or just from data collection to result writeup and reporting (publishing)?

28 February 2021 910 2 View

Is there any limitation of number of variables when doing Panel Data ARDL model analysis in Stata 13.0 version?

I have one dependent variable (HDI) and 14 independent variables within the time period 1990 to 2016. when I run the command (xtpmg.............pmg) the answer is *matsize too small* then I...

23 February 2021 9,448 5 View

Why sometimes current- voltage plot in chemiresistors/ FET does not pass through the origin?

I am trying to measure resistance from I-V curve from a chemiresistor/ FET sensor with a keithly sourcemeter. The substrate is soaked/ wet with protein and phosphate buffer only. But the I-V line...

24 January 2021 8,009 3 View

Any scientific magazine you recommend in order to publish an article?

I want to publish an article and I am looking for a magazine that you recommend

02 January 2021 2,419 4 View

Does book Review in scholarly journals counts as a publication?

Does book Reviews written for scholarly journals or in a magazine count as a publication?

24 December 2020 2,265 3 View

How can i get the data for the FTSE/JSE Responsible investment top 30 index (J110)?

Hi All , Please can you recommend a free database (i already use yahoo finance but it's not avaible) ,or if someone has already worked on this index for the period of 2015 it would be great to...

22 December 2020 247 3 View

Journal of Research in Humanities and Social Science. Is a real magazine?

Dear colleagues: I have received many emails from a magazine called ournal of Research in Humanities and Social Science. I have gone to the website of this journal, and I read "some" indexes but,...

13 December 2020 6,208 6 View

Why there are fewer aptamer-based biosensors and bioassays in commercialization?

Despite the fact of the tremendous number of research papers in the literature dealing with the usage of aptamers as molecular probes in biosensing, and despite the fact that this technology is...

26 November 2020 1,140 3 View

How can we turn a short peptide having affinity for some compound into whole cell biosensor?

Greetings, I have a short stretch of 20 aa with strong binding affinity for a compound. I am trying to de some whole cell flourescence or visible biosensing technique based on this peptide. Can...

26 November 2020 8,322 3 View

How can i define a correct baseline for reading the anodic (forward) peak current when oxygen reduction reaction is distorting my cyclic voltammogram?

Dear colleagues I have troubles to read out the correct anodic peak currents from my cyclic voltammogram since ORR is pushing down my baseline. Is there anything (besides substracting a proper...

23 November 2020 4,654 6 View