Is there any software available to test the effect of wind load over any structure?

H. M.A. Mahzuz @H_Mahzuz2

05 May 2014 1 9K Report

Such software should be equivalent to the result got from wind tunnel test.

Mohamed Ali Bek AbdelRhman

Ansys-Fluent is a good one

Badges
Science topic

More H. M.A. Mahzuz's questions See All

How can i insert or introduce and analyze deformed rebar with concrete in RCC beams in ANSYS?

Can anyone tell please, how can i introduce and analyze deformed rebar in RCC beams in ANSYS? Please share any resource if you want.

01 February 2017 6,166 2 View

Theoretically is it possible to make time slower than that of earth ?

Theoretically is it possible to make time slower than that of earth? Since earth has a motion, our solar system has a motion, our galaxy has a motion....so on. So why not have a reference point...

11 December 2016 7,289 6 View

How to generate a multi variable non linear equation from a data?

Any software, online software or tools???? please mention

11 December 2016 1,900 3 View

Please share any example/ calculation of design of tall or super tall buildings?

Both concrete or seel

07 August 2016 3,567 5 View

Please share any resource or link to design tall buildings?

Both concrete or steel, having different structural systems.

05 June 2016 3,109 3 View

Theorically how is it possible to select the most economical combination of mix ratio for a concrete (e.g. 5000 Psi)?

Theorically how is it possible to select the most economical combination of mix ratio for a concrete (e.g. 5000 Psi)? Is there any procedure?

31 December 2015 5,352 5 View

What do you mean by "TOP JOURNALS" in research gate?

09 October 2015 9,441 0 View

What is the systemetic process of writting a PhD thesis (Engineering field)?

Regarding a systemetic process of writting a PhD thesis (Engineering field)

31 December 2014 6,352 4 View

What is opinion regarding this paper?

special concern: methodology and result

08 September 2014 8,893 2 View

How do you determine the capacity of an existing masonry wall?

Is there any NDT test/code or anything to do such work?

05 June 2014 2,525 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View