Is there any good example of prototypes of rotary MR damper?

30 May 2022 0 3K Report

I am interested in rotary MR damper now.

Is there anyone who knows about the prototypes of rotary MR damper which was applied and tested in the vehicle environments? (flow-type only)

Badges
Science topic

More Youngil Sohn's questions See All

How to treat cells with Kinase Inhibitor to analyze if extra IP bands are due to phosphorylation?

Hey everyone, I bought this kinase inhibitor (Sigma 20-116). It did not come with any instructions/protocols in terms of treating cells with it. I plan to use the cell lysate for an IP. When...

08 February 2024 7,493 0 View

Regarding Bayesian Optimization algorithm, is it possible to implement this using C ?

I would like to check the possibility of implementation of BO using C language. The implementation target is MCU like Tricore or further. Is this possible? Moreover, is there anyone know where...

26 February 2022 7,716 4 View

Can I stain DAPI or phalloidin when using FRET?

Hey! I have a FRET system between the inner and outer nuclear membrane, and I was wondering if I stained with DAPI or any other fluorescent antibody if that would mess up my FRET readout? As of...

06 December 2021 10,046 2 View

Is it possible to optimize control parameters over 500 using AI? What would be the most promising method to do this?

I developed automatic tuner using Bayesian Optimization. The plant system is real vehicle. Furthermore, there is no stability problem, because this system is a kind of semi-active control...

30 November 2021 6,858 5 View

Has anyone used the Corning Matrigel with a Be(2)-c cell line?

Hello, I am currently trying to study cellular stiffness in the Be(2)-c line and I want to use collagen stiffening matrix by corning. Has anyone had success doing this? If so, do you have an...

18 October 2021 4,558 0 View

Why is my FRET donor decreasing during acceptor photo bleach?

I am using the acceptor photo bleach method with Venus and mTFP1. Recently, I have applied this sensor to a model and I was expecting to see an increase in FRET due to less tension, however they...

05 September 2021 5,937 1 View

I am analyzing Acceptor photo bleach FRET data, but when I use ImageJ "image calculator" my donor channel is too weak. Any suggestions?

Hello! I am currently working on FRET using acceptor photobleaching. I have obtained images from a Zeiss 880 confocal. Using the ROI feature, I am able to calculate a 15-30% increase in the donor...

21 April 2021 9,523 4 View

What happens in post-secondary education when instructors don't use traditional grades?

I am looking for empirical studies that examine the use of non-traditional grading in higher education. This means NOT using A-F grades during a course (even if, at the conclusion of the course,...

09 June 2020 1,763 6 View

Vimentin Western Blot: No consistency of the change in vimentin expression level of A549 cell line. What can I do?

I am working on Epithelial to Mesenchymal Transition (EMT) in A549 cell line by treating positive inducers such as EGF to up-regulate the mesenchymal markers like vimentin. I'm doing western blot...

22 May 2019 3,207 1 View

Question regarding Petrel?

I'm just starting to know how to use petrel. and I was just wondering if it's possible to build an anticline or whatever the complex shaped reservoir model just using "simple grid" in RE(reservoir...

29 October 2018 989 6 View

What are the technical requirements for a humanoid cooking robot that cooks at home?

I want to understand what the latest developments are. I am looking for examples, prototypes, ideas

18 May 2024 4,361 0 View

How can I manage the carriers connected to ePWM for code generation using DSP controller to run the MMC five-level output voltage prototype?

I'm currently facing difficulties in conducting my experiment, which aims to investigate the MMC 5-level output voltage using a DSP controller and MATLAB ePWM signals. I would appreciate your...

09 April 2024 3,371 0 View

I have to implement wind energy system in my hardware prototype how can I do so. Is it necessary to use a wind emulator. ?

I need to implement it

26 March 2024 6,324 2 View

In wireless charging system, how to calculate coil parameters according to output power?

For implementing a prototype.

24 March 2024 4,743 2 View

How to find the relative density of the 3D printed cellular structures like honeycomb, double arrowhead?

22 January 2024 7,130 2 View

Where can I obtain a prototype similar to the Images?

I would like to obtain a prototype of a continuous robot similar to the one presented in the following paper: https://doi.org/10.3390/act3030226? I would like to obtain a prototype of a Bionic...

05 December 2023 8,203 0 View

How to get Nissan Chamical or JSR Corp performance materials in Europe?

I am currently doing some R&D prototyping. I need following ingredients from Nissan Chemical: Nissan Sunever polyimide SE 7511L (ca. 100g/100ml) Sunever solvent from JSR...

13 November 2023 2,435 0 View

Ow o calculate any PEM Fuel Cell Stack Size and select the correct Electrolyser based on the Power Requirement ?

Power Requirement is 100 Watts I am developing a prototype model of PEM Fuel Cell Electric Vehicle. So the max speed will be 1.4 m/s or approx. 5.00 kmph. For this I have calculated the power...

08 October 2023 2,281 0 View

What kind of thinner I can use for a viscous photosensitive acrylic monomer used in stereolithography?

I use a DWS System's DS3000, a photosensitive monomer to disperse the nanoparticles in it and use the solution for SLA printing. But, because of its high viscosity, I cannot increase the particle...

03 July 2023 1,598 2 View

Advise the best way to detect cosmic muons. Based on drift tubes or solid-state scintillation strips?

Hi all. Advise the best way to detect cosmic muons. Based on drift tubes or solid-state scintillation strips? To create a prototype muon tomograph. A compromise is needed between the quality of...

21 June 2023 2,138 0 View