Is there any good book for LISREL ?

More Yaser Hasan Salem Al-Mamary's questions See All

I performing the test of moderation for Sex (Male- Female) in AMOS ?

I performing the test of moderation for Sex (Male- Female) in AMOS the male Chi-Square value higher than the value of Chi-Square with 1 degree of Freedom, which is 3.84 but in female Chi-Square...

29 January 2017 9,062 3 View

I performing the test of moderation for (Six) in AMOS ?

I performing the test of moderation for (Six) in AMOS the male Chi-Square value higher than the value of Chi-Square with 1 degree of Freedom, which is 3.84 but in female Chi-Square value lower...

31 December 2016 4,932 3 View

In AMOS, what does it mean by Unique Variable to an Existing Variable?

In AMOS, Why we must to add to the dependent variable "Unique Variable to an Existing Variable ". The value above this icon refer to what ?

07 August 2016 6,684 2 View

In AMOS, what does it mean by error Variable ?

In AMOS, what is the meaning of e1 , e2, e3 etc. The value near e1, e2 , etc refer to what ?

07 August 2016 831 0 View

Is there any good book for LISREL ?

I am looking a book for Structural Equation Modeling using LISREL. Thank you

05 January 2016 1,850 8 View

Is there any good book for SmartPLS ?

I am looking a book for structural equation modeling using SmartPLS.

02 January 2016 9,143 8 View

Is there any good book for SmartPLS ?

I am looking a book for structural equation modeling using SmartPLS.

31 December 2015 5,298 9 View

What are the appropriate theories in field of Delays on construction projects ?

Any suggestions?

10 November 2015 9,169 0 View

Does anyone know of any free Scopus journals that respond quickly?

Most journals respond in around 6 - 9 months. In addition, some journal reject the paper after waiting for 9 months. I am looking for a journal in the field of information systems or management...

09 October 2015 7,918 2 View

In case of multivariate normality if the data not normal. Can I ignore the normality and continue analysis?

Excuse me, I need literature to support that " In case of multivariate normality if the data not normal the researcher can ignore the normality and continue analysis ?". Thanking you

02 September 2015 4,915 23 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Yopie Yutama Surbakti

Dear Mr. Al-Mamary,

I got a book that may help you. This book is suitable for beginner in order to understand basic concept of SEM using LISREL. Wish you the best, Mr. Al-Mamary

Yaser Hasan Salem Al-Mamary

Prof Yopie Yutama Surbakti thank you very much

Karin Schermelleh-Engel

Yaser,

here is a documented LISREL input file which may be helpful for you.

Regards,

Karin

Prof Dr. Karin Schermelleh-Engel thank you very much.

Mahmoud Moussa

http://www.ssicentral.com/lisrel/techdocs/GSWLISREL.pdf

Prof Mahmoud Moussa thank you very much