Is there any correlation between Avrami exponent on precipitation (KJMA theory) and coarsening exponent (growing laws, e.g. LSW)?

21 February 2019 1 7K Report

I am studying borocarbide M23(B,C)6 precitation and coarsening kinetics on boron-added medium-carbon low alloy steel. The data fit results on very similar precipitation Avrami coefficient (n) and coarsning exponent (also n).

Thanks in advance.

Ahmed Hmeed

Badges
Science topic

More João Gomes Antunes's questions See All

Is there an English Translation of the Carl Moller text: ZUR VERGLEICHENDEN ANATOMIE DER SILURIDEN?

I recently came across an anatomy text by Carl Moller that was published in 1915 but it is in German or Dutch neither of which I can understand. I would like to know if there is an English...

10 August 2024 4,347 1 View

What publications should I target as a psychology masters student in the UK?

I am writing a paper as a part of my course. I am new in London and was wondering that what publications should look upto?

21 July 2024 3,538 1 View

I have two problems: 1) the enzyme is not immobilizing efficiently into the MOF material.. 2) the MOF itself has peak on 400nm by using p-NPA test.?

I am working on carbonic anhydrase immobilization into MOFs. I am facing problems with low enzyme loading.. The other issue is that when using p-NPA activity test to detect the activity of the...

20 July 2024 1,440 3 View

What analysis to use for an dependent variable with repeated measures and a independent variable only measured once?

Hi all, I am trying to use mixed effect model to analyze my data, which including a baseline measurement for my exposure (A), and repeated measurements for the outcome (B). I do have some...

17 July 2024 8,682 3 View

I need to know the required time for VDF heating with water for 50-80°C for PVDF Polymerization in ?

i need to know the required time

15 July 2024 4,796 2 View

What analyzes do you use to compare biodiversity in a square, at two different times?

e.g. moment one: square in its normal state moment two: square after cutting large trees and replacing them with dwarf trees.

12 July 2024 8,258 5 View

Which software use to i make this graph quickly and also make more dimensions of this graph( i mean adding vertices or lines in this graph)?

Anyone kindly tell the name of software that make this graph quickly and also tell how we add vertices or lines in this graph with equal distance to get next dimensions of this graph ( i mean how...

11 July 2024 4,499 2 View

Authorship for data analysis?

I participated in 2 research projects in which I was responsible for part of data analysis and figures production. Also, I spent hours trying a new statistical approach -for me- to implement in...

10 July 2024 1,226 5 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View

How to determine the quantity/amount of secondary phase based only on peak intensity?

I have 3 different specimens. Each specimen has a main peak of the targeted phase, however, all of them also have a secondary peak of associated with a secondary phase. Now just based on the...

26 June 2024 5,049 5 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View