Is there any analytically correlation to calculate the penetration of a inclined turbulent air jet into a heated crossflow?

Anoop Asranna @Anoop_Asranna2

03 March 2015 1 9K Report

Or, how is the penetration depth for a jet defined? Can it be deduced from simulation results?

Savas Yavuzkurt

See p. 175 eqn 41 in

Full-coverage film cooling. Part 2. Prediction of the recovery-region hydrodynamics

S. Yavuzkurt

Savas Yavuzkurt R. J. Moffat W. M. Kays

http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=4&ved=0CDYQFjAD&url=http%3A%2F%2Fjournals.cambridge.org%2Farticle_S0022112080001589&ei=DlYPVefvGsOkNr2ngbAB&usg=AFQjCNHX0EbfIMM3Rc-Ku7HDwAxLd7aipQ&sig2=b6gKITEZ3iUeYBnX1-P6BA&bvm=bv.89060397,d.eXY

Badges
Science topic

More Anoop Asranna's questions See All

How is the compressible NS equation solved in COMSOL?

I use the 'non-isothermal flow' module in COMSOL 4.4I am trying to understand how COMSOL exacly solves the NS equations..I know the equations used (mentioned in the user's guide)..There are ample...

04 May 2015 3,537 3 View

How does COMSOL solve for low Mach number flows? What are the pre-conditioning techniques applied?

Hello all,I am looking to model flow in a combustion chamber where the flow is compressible because of the temperature variations and not due to pressure. The Mach number

04 May 2015 2,468 1 View

How to incorporate passive scalars onto my simulation model?

I am simulating a turbulent jet in a cross-flow for which I need to make use of passive scalars. Is there a way I can do such an analysis in COMSOL?

02 March 2015 2,271 2 View

How can I obtain Reynold's stresses from COMSOL/CFD?

I am simulating a high re turbulent jet in COMSOL using the k-omega model. I am looking to obtain the values of the turbulent stresses. I have the value of the turbulent kinetic energy, how do I...

02 March 2015 9,494 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View