Why can't I observe XRD peaks of nanoclay in polymer matrix?

Dear All, I added different amounts of nanoclay (e.g. wt% 1,3,5) in my polymer matrix. I couldn't observe any peaks related with my filler especially for 1 and 3 wt%. I tried to change slits,...

11 December 2018 4,656 10 View

Where can I find nanosized PP particles?

31 December 2015 5,638 7 View

Where can I find polypropylene microspheres?

I'm looking for polypropylene microspheres to use them in microfluidics. I will appreciate for any help.

09 October 2015 4,485 4 View

How can I determine concentration of solutions for electroless plating?

I want to coat my millimeter sized sample with electroless coating process. First of all I need to sensitize the surface with SnCl2 then activate it with PdCl2. I implemented all of the steps...

05 June 2015 7,581 6 View

How can I remove polypropylene from plasma bonded glass surface?

02 March 2015 2,440 3 View

How should I mold metallic bodies in micro scale?

31 December 2014 6,871 9 View

How can I disperse prussian blue in water ?

31 December 2014 5,772 3 View

How can I have a good adhesion between metal and polymer?

Is it possible to provide a strong bonding between metal and polymer interface via plasma process ? What are the possible conditions to have this ?

31 December 2014 7,182 17 View

No title

11 December 2014 769 1 View

How can I refine silver scrap which includes %1Sn?

As far as I know it is not possible to refine it by using electrorefining. My question is that what are the possible steps that I should follow?

11 December 2014 7,141 2 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

What should a smart water system look like?

Our team is designing a smart water C&C dashboard for a smart city initiative. As we look into the current smart water system landscape, we couldn't reconcile to a definitive solution that...

16 February 2021 1,094 3 View

Receiving very less number of hits and events in acoustic emission tests?

I am doing a three point bend test with concrete specimen of dimension 280mm*90mm*90mm. I am putting 2 sensors near the notch with 3cms away from both the sides. the experiment ran for 20 mins but...

13 February 2021 2,990 1 View

How to increase coupling range (distance between reader and sensor coils) in LC resonance circuit?

Hello great researchers, I am working on a wireless pressure monitoring project where sensing part is actually an LC resonance sensor and I am using a planar coil as a reader to get wireless...

11 February 2021 4,148 5 View

I am looking for a microbend optical sensor design...can anyone please provide me some idea about it??

I am working on a landslide model...i need an optical sensor to determine the amount of pore pressure and other values..i am thinking of using a microbend sensor. Can anyone please provide me with...

11 February 2021 5,911 2 View

How to eliminate noise when using a sensor with instrumentation amplifier and giving it's output to Arduino?

When I am trying to implement a pressure sensor through instrumentation amplifier and then giving it's output to Arduino, I am getting garbage value due to noise, so how to eliminate it.

05 February 2021 8,598 11 View