Does anyone have experience with acceleration at the beginning of Abaqus/Explicit after results transfer from Abaqus/Implicit?

07 August 2014 2,554 11 View

Can anyone help to establish the contact state after an importation from abaqus/Standard to abaqus/Explicit?

Hello everyone, I performenced a 4 point bending calculation in Abaqus/Standard, and then I imported the resultats to Abaqus/Explicit to do a dynamic job. Due to the difference of the contact...

07 August 2014 6,892 5 View

Is it possible to co-utilize XFEM and cohesive elements in Abaqus?

I have a question about the feasibility concerning the co-utilization of XFEM and cohesive elements in Abaqus. In fact, in the documentation, they did mention that XFEM could be simultaneously...

05 June 2014 3,031 10 View

Can anyone help with grain boundary simulated by cohesive surface in Abaqus?

I'm doing a simulation for a thin plate polycrystalline subjected in pure bending, and I consider the grain boundaries by the surface interaction using the cohesive surface behaviour in Abaqus....

04 May 2014 7,141 1 View

Does anyone have information about Abaqus XFEM based on the LEFM-initiation of crack?

Does anyone know about the Abaqus XFEM based on Linear Elastic Fracture Mechanics? The question is about how the fissure initiates under this finite element analysis framework. It's not like the...

03 April 2014 2,628 11 View

What is wrong with the STRESS values in UDMGINI user subroutine in Abaqus?

I wrote a subroutine UDMGINI to define a damage initiation criterion, but I found that the variables of stress were very strange. I kept track of stress (NTENS) using the state variables STATEV,...

03 April 2014 1,851 13 View

Can anyone help with simulation using XFEM in Abaqus?

I am trying to simulate brittle crack without initial crack using Abaqus XFEM. Specifically, I make a simulation of the 4 point bending (contact problem) on a very thin orthotropic plate...

02 March 2014 6,678 2 View

Construction of the grains' forms to be used in a Finite Element calculation?

In fact, I have a mechanical calculation on a piece consisting of grains whose grain boundaries are clearly visible. So I intend to build the grain boundaries. I have gotten an image taken by a...

01 February 2014 632 0 View

Damage model for initial anisotropic materials?

Does anyone know if there are some damage models that can be applicated on initial anisotropic materials?

01 February 2014 2,249 3 View

How to determine viscoelasticity on an anisotropic material in Abaqus?

Does anyone know how to perform a calculation of viscoelasticity on an anisotropic material in Abaqus/CAE? Thank you very much

11 December 2013 282 6 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View