Any one known the correlation between the proton conductivity in out of plan and in plan of the polymer membrane?
Check this article
doi: 10.1149/1.3635668
ECS Trans. 2011 volume 41, issue 1, 1371-1380
Dear Dr. Sujoy, Thank you so much.
I will be glad if you can send me this article "[email protected]"
Thanks a lot
Source to get Impact factor of journals
01 March 2021 6,654 2 View
I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...
28 February 2021 2,004 3 View
I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...
26 February 2021 9,580 4 View
25 February 2021 6,760 1 View
Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...
22 February 2021 7,528 3 View
I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...
17 February 2021 7,402 4 View
Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...
09 February 2021 6,799 8 View
07 February 2021 3,635 3 View
Hi, We find a specific distribution of electric fields in structure for different frequencies which can be seen using em solvers and known as modes. I would like to know how we can choose the...
04 February 2021 10,043 3 View
If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers can i use the same word in the writing of these 2 papers or this would considered as...
04 February 2021 4,648 4 View
What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help
08 May 2021 0 0 View
Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...
02 March 2021 4,119 3 View
In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?
01 March 2021 1,923 3 View
Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...
28 February 2021 7,882 2 View
I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...
28 February 2021 298 3 View
28 February 2021 2,534 2 View
What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?
28 February 2021 6,516 5 View
Its effect appears in real part of ac conductivity also. Can anyone suggest any reason behind it?
26 February 2021 3,487 3 View
I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...
25 February 2021 2,615 3 View