Is the exrgy efficiency in inversely proportional with the comfort conditions?

More Hayder Jaffal's questions See All

How to solve melting and solidification of PCM using ANSYS Fluent?

Dear colleagues; I modeled 3D melting and solidification of phase change material filled heat exchanger and generated a (as in the picture below). First, I enabled melting and solidification...

19 January 2021 1,126 4 View

What are the shape functions of rectangular Q4 and triangular CST element models in natural coordinate system with (s,t) that ANSYS APDL will be used?

What are the shape functions of CST triangular and Q4 rectangular element models in terms of natural coordinate system (N.C.S) with (s,t) not with (x,y) in software programs as ANSYS mechanical APDL?

13 January 2021 7,968 4 View

What's the best suitable area element type like 182,and 183 quadrilateral and triangle for analysis of 2D FE modeling results, beams in ANSYS APDL?

I want to analysis of 2D FE modelling beams cantilever/simple support in ANSYS, then compare it with exact solutions (elementary) such as deflection or stresses, however what element types (solid...

07 January 2021 8,744 1 View

What's the best appropriate area element type like 182,and 183 quadrilateral and triangle for FE modeling results,analysis of 2D beams in ANSYS APDL?

I'm trying to carry out analysis of 2D FE modelling beams cantilever/simple support, then comparing it with exact solutions (elementary) such as deflection or stresses, but what element types...

06 January 2021 1,038 3 View

Why does bending stress(Sx) in ANSYS APDL direct below of point load FE 2D modelling simply supported point load higher than exact solution in value?

Why does normal bending stress/flexural stress value (Sx) just direct below a concentrated load of simply supported beam which is compression stress higher than the hand calculation Exact solution...

03 January 2021 8,462 3 View

Why does shear stress (Sxy) result in ANSYS APDL area element type solid 182 or 183 quadrilateral or triangle will be efferent in a cantilever beam?

Why does shear stress (Sxy) result in ANSYS APDL area element type solid 182 or 183 quadrilateral or triangle will be different in a cantilever beam with point load at fixed end or uniform load at...

31 December 2020 9,359 3 View

How to show effects of baffles on fluid flow?

Hello All I'm working on baffles inside a circular pipe, the problem that I'm facing is when I draw contour or streamlines, I have not found any effects for the baffles on fluid flow where fluid...

23 October 2020 2,002 3 View

How to select best Probability Distribution Function (PDF) for time series of extreme value data sets based on multiple Goodness of Fit (GOF) tests?

I have prepared an analysis of time series extreme values data sets (9 sets for different storm durations) by using three PDFs i.e. General Extreme Value (GEV), LogPearson III (LP III), and Gumbel...

11 October 2020 3,331 2 View

Can oligo hexamer primer produce sequencing error?

Hello everyone I conducted sequencing prosedure for RNA genome segment (about 700nt) , for this reason I employed the random hexamer primer for cDNA synthesis . after sequencing (by sanger...

16 August 2020 3,994 3 View

How do I know which type of mesh and its method is suitable for my geometry in ANSYS? How do I choose the right mesh?

If I wanna work on geometry and wanted to create a mesh for it, how can I be sure that my mesh I choose it is the best to give the right results

21 January 2020 6,095 4 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View

Hayder Jaffal

Dear Aleš

Thanks for your cooperation

Mehdi Aliehyaei

Dear sir

Exergy efficiency defines comfort/energy usage, you should use this term and define new formula for summer.

Dear Mehdi

Thanks for answering.

Is this definition of the exergy efficiency is general definition or related only over human body?

I greatly appreciate your comment.

Many thanks