Is t possible to link CMG VS ECLIPSE 100,or ECLIPSE VS CMG ?

Mahamat Tahir abdramane Mahamat Zene @Mahamat-Tahir-Mahamat-Zene

23 February 2019 1 1K Report

The result will be compared one each other from the software. I knew it is possible to import eclipse to cmg imex, but i am interested in the results comparison like you compare different sensitivity cases into 1 software.Thanks for your guidance and help.

Mahamat Tahir abdramane Mahamat Zene

Yes,it is possible import eclipse data to CMG IMEX.

Badges
Science topic

More Mahamat Tahir abdramane Mahamat Zene's questions See All

How to figure out easily the right journal with the right scope for your paper?

According to my experience most of the selected journals during paper submission are based on journal text matching suggested results from Springer, Elsevier,,,Etc. then the manuscript happened to...

01 March 2021 1,786 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

Is there any software or formula for sample size determination by using sensitivity and specificity?

I want to conduct research on the diagnostic performance of some tests. I want to calculate sample size by using the sensitivity and specificity of the test in the previous studies. So Is there...

23 February 2021 619 5 View

What is the best way to track bird migration?

Migratory birds are globally scattered. What should be the ways to track them? Except ARGOS. Elaborate.

25 January 2021 2,355 4 View

How i can reduce the number of atoms using Vesta ?

I'm a new Vesta learner, I have downloaded cif of Ch3Nh3PbI3. Total number of atom in chemical formula for Ch3Nh3PbI3 is 12. But when i convert this cif to poscar file using Vesta, total number of...

14 January 2021 5,733 11 View

How to determine the sample size for ANOVA in GPower?

Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...

19 December 2020 3,600 4 View

How to calculate the replacement cost of battery?

As battery needs to be replaced after the specific charge and discharge cycles mentioned in the datasheet. If we have the time series data of battery power and energy capacity, then how can we...

01 December 2020 3,433 3 View

Can anyone please elaborate the relationship between charge and discharge cycles and battery lifetime?

I am designing the optimal HESS capacity for the renewable system. I have to select the cutoff frequency of low pass filter to divide the low and high-frequency components. charge and discharge...

05 November 2020 8,397 3 View

How to select the frequency range in MATLAB Wavelet toolbox?

I have a continuous, time-domain noisy signal and want to decompose into low-frequency (LF) and high-frequency(HF) components using Wavelet Toolbox. But, I am unable to select the frequency range....

29 October 2020 5,219 5 View

How can I retrieve information of viruses reported from a particular region/country ?

Dear All, Can anyone please guide me on how to get information (sequences) of plant/animal viruses from a specific region ? Looking up the published literature is one way but its time-consuming,...

19 October 2020 3,958 1 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

How to visualize stress in a coating defined by "Skin" in Abaqus?

Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...

16 February 2021 1,594 3 View

How to perform Cox proportional hazard analysis or Kaplan-meier survival analysis in SPSS?

At first please see the attachment. This experiment was performed for a period of 7 days (n=100). After 7 days, we found different level of survival rate (%) for each treatment. Now, I want to...

15 February 2021 9,145 2 View

How to calculate visual angle of a visual stimulus?

I am currently trying to figure out how to calculate the visual angle of some visual stimuli I used in an experiment. I think I have all of the information I need to calculate this. One is a...

15 February 2021 3,189 2 View

Hyperspectral Image : open, visualize, process in Python?

I am looking for a tutorial or course to learn how to open, visualize , process hyperspectral images in .hdr , .raw format using python. Any recommendation for a tutorial is appreciated ? Thank...

08 February 2021 7,896 3 View

Recommendations for sample size in visual qualitative research (using children's drawings)?

Hi everyone! Asking for a little help, if I may. I am working on a research project, where I aim to analyse children's drawings about Covid-19. I am fairly new to using visual data in qualitative...

07 February 2021 9,530 3 View

How To Properly Show Displacement Versus Force For A Capacitive Parallel Plate With Multiple Electrodes in COMSOL?

I want to determine through simulation in COMSOL the displacements due to applied forces. The sensor has 4 bottom and 4 top electrodes that do not complete align along with a bump on top which...

21 January 2021 6,856 3 View

Inexpensive eye tracking hardware + software solution?

Hello, I am starting a project that will require an eye tracking device. I've seen eye tracking hardware + software solutions that are $10,000+ so I am hoping to find one that is significantly...

18 January 2021 8,121 12 View

Is it possible to combine two continuous variables into one categorical variable in order to create a dummy in SPSS ?

As background, in my model, my independent variable is visual clutter which has two conditions (higher visual clutter/ low visual clutter) and the conditions measure the amount of visual clutter...

13 January 2021 4,760 4 View