Is it possible to develop self healed polymer matrix composite in which strength of healed structure greater then strength of virgin structure?

More Nishant Verma's questions See All

How to increase the porosity of PLA (Polylactic Acid) based composite?

i am working on Polymer based composites and developing PLA ( Polylactic Acid ) based composite for XYZ applications. When i observe the resultant composite on SEM i find the porosity only on...

05 June 2018 7,217 0 View

Which indexing is better?

what is difference between Science Citation Index Expanded and Science Citation Index. both are same or different?

05 June 2018 747 3 View

How much similarity index is acceptable for sci indexed journal?

I am writing a paper and some words and lines are common to my previous paper just because my present research work is extension of my previous work, that is already published. The similar index...

01 January 1970 4,238 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is it true that $\det(V(A))$ may be only $\pm 1$, depending on $n$, for the last symmetric tridiagonal matrix $A$?

One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...

08 August 2024 6,690 1 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,084 6 View

Request a single Lecture notes for math as detailed as this that I can find in one place?

- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...

03 August 2024 2,366 0 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Tissue homogenization in mouse with FastPrep-24™ 5G - is the D matrix system useful?

I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...

31 July 2024 9,186 0 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View