Is it possible to calculate analytically longitudinal creepages, lateral creepages and spin moment for rail wheel interactions ?

More Sunil Kumar Sharma's questions See All

What is the permissible value of jerk longitudinal for passenger rail vehicles?

What is the permissible value of jerk longitudinal for passenger rail vehicles? I need a jerk limit value in the longitudinal direction. also, the reference of it

01 February 2017 3,322 0 View

Rail wheel contact ?

Is any one is having any matlab code for strip method or non hertzian contact

02 March 2015 5,361 1 View

Which method is best for calculating contact force between rail and wheel ?

Which method is best for calculating contact force between rail and wheel? Like non hertzian contact theory or kalker or other .

02 March 2015 1,945 4 View

What component to be consider for a Track modeling ?

To model a track what are the component that has to be consider and how to go for mathematical modeling .

02 March 2015 4,215 1 View

If i want to work for semi active suspension system for railways can any one help me how to do that work ?

Semi active suspension system for semi high speed train

01 February 2015 9,169 0 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Rakesh Chandmal Sharma Popular answer

YES IT IS POSSIBLE TO DETERMINE THE LINEAR LATERAL, LONGITUDINAL, SPIN CREEP EXPRESSIONS ANALYTICALLY. THIS IS ANALYSED BY ME IN MY DOCTORAL THESIS. (ATTACHING THE REQUIRED PORTION FROM MY THESIS.

DR RC SHARMA

Altan Onat

"A New Method for Modelling and Simulation of the Dynamic Behaviour of the Wheel-rail contact" by Anyakwo et. al. has a small chapter about how creepages including spin creepage can be calculated.

Hope this helps.

Best regards.

Rakesh Chandmal Sharma