Is it good to go with ETAP software for distance relaying scheme for transmission line? Or to do with it other software?

More Chintan Varia's questions See All

Which are the advanced objectives of parametric optimization of Wire cut EDM machining of the MMC AlSiC?

Is there any further objectives like fea of WEDM and other methodology used except optimization in Wire cut edm of AlSiC MMC material?

30 January 2023 5,971 3 View

How to categorise proteins based on the function?

Hi all, I wish to classify my proteins into the classes like the one in the attached image. I tried various bioinformatic tools including DAVID, panther, and gene ontology. However, they don't...

22 January 2023 7,101 2 View

Can I use HNO3 as solvent to make cerium oxide nano particles in sol-gel method? and the process I followed is sol-gel method or co precipitat method?

Cerium(III) nitrate hexahydrate [2 g, Ce(NO3)3·6H2O] was dissolved into 4.5M HNO3 (5 mL). Sodium hydroxide (10.50 g NaOH) was also dissolved into DI water (deionized water) (35 mL). This NaOH...

06 November 2022 8,602 3 View

What is the possible solution to the error "turbulence viscosity limited to viscosity ratio 1.000000e+05 in xxxxxx cells" in ANSYS Fluent?

Hello everyone, I am working with multi physics eulerian modelling in ANSYS. I am using k-epsilon model to work with simulation. Simulation is regarding stirring of molten Al in crucible or say...

28 April 2022 2,184 0 View

Why most of researcher used Wrought Al alloy to prepares Al MMC using stir casting process?

Wrought Al is already extruded grade then why most of researcher are not using Al cast grade And very few researchers worked on cast Al grade during stir casting. If one can given insight on why...

09 November 2021 2,138 4 View

Respiratory syncytial virus plaque assay?

Hello, I am trying to perform a respiratory syncytial virus (RSV) plaque assay. I can see the syncytial formation, white dots with a crystal violet background (3 replicates). However, I don't see...

18 October 2021 5,082 2 View

Which AlSiC compnent used in automobile, aerospace etc. manufactured by using Electric Discharge Machining Process ?

I have observed many papers in optimization of electric discharge machining on different MMC compositions. But, nowhere I found application of EDM for such parts. I want to know which AlSiC...

27 June 2021 3,290 1 View

How can we count the number of edges in an edge detected image using canny/sobel algorithm in MATLAB?

I need to process an image for edge detection and then want to count the number of edges in that image.

29 December 2020 5,961 2 View

Is there any workaround for MaxQuant when it crashes unexpectedly without giving any errors?

I am processing my MS results that were acquired in Orbitrap instrument and it seems that as soon as I start the analysis on MaxQuant, it crashes unexpectedly with any error reports. This has...

01 October 2020 8,132 6 View

How to use Fischer exact test for daily survival analysis? Can I do it in SPSS?

I want to compare survival difference daily using Fischer exact test? How do I do get using SPSS?

12 June 2020 7,348 3 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

To perform transfection with DharmaFECT Duo in AGS cells. Could you tell me what the ideal concentration is to avoid significant cytotoxicity?

I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...

03 August 2024 3,851 1 View

Which test should be used to study association among demographic profile and awarness level?

i have to study the awareness and adoption level of cloud computing in a district of India. i also want to use association among demographic variables like gender, age, education, income etc and...

02 August 2024 2,420 3 View

Why 3 replicates for most biological assays? Is it enough to examine the data fits normal distribution?

Just bounced on me. Before statistically analysing significant difference, shouldn't we see if data fits normal distribution first? Is 3 replicates enough to testify the hypothesis of normal...

31 July 2024 8,141 13 View

Mario R Arrieta Paternina

ETAP works very well in protection schemes on distribution systems. I suggest you use DIgSILENT Power Factory for distance relaying in transmission lines.

Best regards,

Mario AP