Is there any study to generate solidification temperature profiles using machine learning?

We know that time dependent temperature profiles can be generated using methods like FEM which solve PDEs. Can we do same using machine learning? Has anyone come across any related study?

25 January 2021 135 3 View

What etchant should be used for Annealed 17-4 PH stainless steel sheet ??

I wish to determine microstructure of 17-4 PH stainelss steel sheet (annealed condition). What etchant should I use so that a clear microstructure can be found out ??

03 January 2021 9,836 2 View

What is the difference between PEEQ, PE and LE options in abaqus ??

I wish to find out thickness variation in my model, so for that which one I should choose among PEEQ, PE and LE ??

26 December 2020 6,542 2 View

Do you think selfishness and opportunism are key to the success?

Do you think selfishness and opportunism are key to the success? Dou you agree that principles, morals, ethics, intelligence etc. are only useless, show-words, even in the fields of science,...

24 December 2020 10,015 12 View

What should be written in Article Highlights?

My manuscript has been accepted in SN Applied Sciences. New comments tell me that there should be 'article highlights' below Abstract. Article Highlights section comprises of three bullet...

03 December 2020 9,045 2 View

How to derive free energy functional equation in Phase-field modeling?

I am going through research papers in phase-field modeling and every paper has different free energy functional equation. Where those equation come from? How to decide which equation is...

12 November 2020 5,918 2 View

What is main difference between wrought alloys and cast alloys in general?

I have been asked this question so many times. I give a general answer based on a metallurgy book which states that 'wrought iron can not be cast'. However, you can cast wrought aluminum alloy...

12 November 2020 5,163 9 View

How to plot thickness contour plot and load diaplacement diagram in stretching simulation in abaqus ?

How can we plot thickness contour plot in stretching simulations in abaqus. Thickness contour plot means variation of thickness with time as stretching takes place. How can we plot load Vs...

10 November 2020 1,019 3 View

How to evaluate tensile test results in research paper?

I have submitted a manuscript on resistance spot welding. I have used lap-shear tests for joint strength. I have shown those results in a table against experimental combinations of process...

26 October 2020 8,824 7 View

What are the methods to automatically annotate a large dataset of images?

Computer vision, Deep learning

22 October 2020 6,027 5 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View