Ion milling rates for NiO and stainless steel?

26 April 2019 1 996 Report

Hi,

I am looking for Ion milling rates for metal oxides as NiO and stainless steel. Does anyone have experience in those materials or something similar?

Thanks a lot,

Ana

Rabih Kamel Hassan

Hello

about 12.1 micro meters per hour for Nickel and 11.3 micro meters per hour for stainless based on energy of 5kv beam size 1.5mm.

Badges
Science topic

More Ana Zuzuarregui's questions See All

A variable moderating multiple relation - how can I test hypotheses using amos?

How can I analyse the relationship between five independent variables and one dependent variable, with a moderating variable influencing each of these five relationships? How can I test hypotheses...

03 June 2024 6,221 1 View

Any experience in fibroblast centrifugation?

We are experiencing different problems pelleting fibroblast: a) From the resuspension of the comercial vials (after defrosting, we resuspended in 5ml complete DMEM + L-Glutamin + FBS +...

28 May 2024 3,529 1 View

Fibroblast trypsinization in Hanks medium with Ca and Mg?

We are setting up fibroblast cultures in a new location and we had to change the mediums suppliers. At the trypsinization step trypsin did not work and we realized our hanks medium has Ca and Mg....

28 May 2024 6,052 2 View

Are the calibration curves of NO radical scavenging assay asymtotes?

Hello. I am here looking for help with the NO radical scavenging assay. I was working on setting up the assay with sodium nitroprusside and the Griess reagent as they do in most works. However, I...

27 May 2024 5,013 1 View

Inconsistente results with cell line LX-2, any advice?

Hi there! I'm working on my master's thesis and for my project I'm testing a new curcumin derivative in liver fibrosis. I'm working with the cell line LX-2 and have been having problems since the...

21 May 2024 2,171 0 View

Will ultracentrifugation be replaced as the most widely used method for isolating extracellular vesicles?

Ultracentrifugation is the most widely used method for isolating extracellular vesicles (EVs), despite the significant structural damage that EVs suffer during the process.

16 May 2024 9,432 1 View

¿What control can I use to inhibit the proinflammatory effect of LPS in macrophagues?

I want to evaluate the polarization to M2 phenotype in Raw Cells, I co-cultured the cell with LPS and my drug to see the effect of the drug to inhibit the proinflammatory effect of LPS, but I have...

05 May 2024 8,525 0 View

Scientific support for research in Dentistry University of Los Andes Venezuela?

Sirs. ResearchGate Receive a cordial and respectful greeting. For academic purposes only, we request collaboratively the following articles for one of our research professors, who is preparing...

05 May 2024 9,459 9 View

How can we prevent small peptides (1000 Da) from eluting out of the gel during staining in a peptide gel (tricine-SDS-PAGE, Shagger)?

How can we prevent small peptides (1000 Da) from eluting out of the gel during staining in a peptide gel (tricine-SDS-PAGE, Shagger)? There are different types of fixing solutions, but I'm not...

28 April 2024 1,522 0 View

Which are Australia regulation for disposal of produced water from oil and gas activities?

I am currently conducting research for my PhD on environmental regulations, specifically focusing on the disposal of produced water from oil and gas activities in Australia. I would appreciate any...

18 April 2024 1,544 1 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Problems with ion exchange chromatography?

I'm having problems with ion exchange chromatography. After applying my sample (a fluorescent protein), a preferential path inevitably forms. The matrix I use is DEAE-Sephacel. Could someone...

27 July 2024 6,605 0 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

How can I regenerate a SCX column modified with Sulfonate group (Thermo 054995)? The colmun has lost its Resolution and peak to valley ratio?

The column is used in Ion Exchange Chromatography of Monoclonal antibodies and the method of analysis is based on pH gradint.

13 July 2024 7,462 1 View