Ion exchange - FAQS.TIPS

Tahereh Naderishahab @Tahereh_Naderishahab

01 January 2013 1 5K Report

I want to do an ion exchange of cu+ and glass but I cannot get it to take place. I have done it like in the explanation.

I added NH4Cl to CuCl and mixed them, put it in the crucible with the glass, and put them in the furnace at 500 degrees Celsius but nothing happened.

Zol Bahri Razali

You can get the similar or apropriate answer by searching the keyword in the GOOGLE SCHOLAR page. Usually you will get the first paper similar to your keyword.

From my experience, this way will help you a lot. If you still have a problem, do not hasitate to let me know.

Kind regards, Dr ZOL BAHRI - Universiti Malaysia Perlis, MALAYSIA

Badges
Science topic

More Tahereh Naderishahab's questions See All

What is the difference between the design of a ordinary waveguide and recipropcal waveguide?

I want to know how to design a nonreciprocal waveguide. I'm not sure if the only difference between these two waveguides is only the material used to design them.

03 April 2016 6,278 2 View

Can anyone explain what is "extinction cross-section"?

I came across this in mie theory

09 October 2013 1,845 15 View

I want to do an ion exchange of cu+ and glass but I cannot get it to take place. I have done it like in the explanation.

I added NH4Cl to CuCl and mixed them, put it in the crucible with the glass, and put them in the furnace at 500 degrees Celsius but nothing happened.

31 December 2012 9,771 0 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How to dissolve cross-linked Amberlite IRC120 H, hydrogen form resin?

Hello all, I have used Amberlite IRC120 H, hydrogen form acidic cation-exchange resin for the ion-exchange of waterglass [sodium silicate solution -- 40% Sodium silicate (mol ratio > 3.2)...

21 February 2021 5,614 3 View

How to prepare electrolyte of NaClO4 salt for Na-ion battery? Any problem with this salt?

Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...

21 February 2021 8,132 1 View