I am studying soil-structure interaction with Abaqus software. I can model the contact between solid-solid elements.However, it takes much time even in elastic analysis.
Is there a way of modeling contact between solid-beam elements in Abaqus?
Embedded region constraint will surely help in modelling B31 and C3D8 contact or you can try multi point constraint(MPC)
Dear Haroon Rashid ;
thank you for the resaponse.
I have successfully applied embedded region. However, the interaction between solid-beam elements cannot be modeled with this type as I know.
Hi everyone, I am conducting a non-linear multi-layer pavement structure analysis which is a stress-dependent. So far, I am able to define the nonlinearity for one soil layer for its resilient...
11 February 2021 9,607 3 View
The scope of emergency and disaster management systems should be redefined. Public transport and fleet management pandemics must be inclusive. Logistic management and Intelligent Logistic...
03 February 2021 3,132 2 View
I have an alkaline solid waste which contains the following components: SiO2, Al2O3, and CaO according to the XRF analysis (as it gives the results as oxides). However, I know from the XRD that it...
28 January 2021 9,469 3 View
What is the best finite element modeling software packages for modeling non-linear and fracture analysis of CONCRETE? I've had some with ABAQUS standart/explicit, but I would like to learn if...
27 January 2021 330 6 View
Dear Researchers, I am trying to model a gasification process for biomass on DWSIM. (Aspen plus is expensive and unreachable). I have been doing lots of searches but couldn't find anything. Is...
02 January 2021 842 4 View
I am using COMSOL for patch antenna design and i have a problem in the 3D Far Field, Virtual Array > Far Field 1 expression...
02 January 2021 7,736 1 View
Hello I'm trying to model a reinforced concrete frame in Abaqus using CDPM for concrete material. I have entered damage parameters as well. Longitudunal rebars were modelled as 3D solid elements....
17 November 2020 5,498 10 View
I am studying Modern English Novel, spcifically postmodern and postcolonial novel. I am very indecisive about determining a topic. Is there anybody recommending me about a topic relating with...
05 November 2020 6,434 9 View
INPUT [32x32x3] will hold the raw pixel values of the image, in this case, an image of width 32, height 32, and with three color channels R, G, B. If we decide to use 12 filters this may result...
15 June 2020 2,833 2 View
Could you please share your ideas about using deep learning for long-term forest management planning. Thank you all in advance.
08 June 2020 5,690 9 View
I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...
01 March 2021 10,078 1 View
I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...
01 March 2021 6,661 3 View
I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...
01 March 2021 736 3 View
Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...
01 March 2021 9,511 3 View
Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...
28 February 2021 3,442 2 View
I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...
28 February 2021 4,841 3 View
I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...
28 February 2021 5,415 1 View
I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...
27 February 2021 6,818 3 View
Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...
25 February 2021 9,936 2 View
I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...
24 February 2021 4,908 5 View