In magnetron what is pie(π) mode and why it is prefer?

More Shyam Gopal Yadav's questions See All

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Articles on" Gender disparities i leatherwork education"?

Articles on" Gender disparities i leatherwork education"

07 August 2024 2,500 0 View

Is Galaxy.org good to use for research for analyzing data and for publication?

Hello all, I wanted to know, can I use galaxy (USA, Europe or Australia) platform for analyzing the shotgun data, and can it be used for publication purpose as well? Thanks :)

06 August 2024 6,610 4 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

What should Berlin do as a city to become as impactful as London and Paris in World Football?

Please go through my Abstract. I can also share a proposed Thesis Outline.

04 August 2024 2,077 0 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Why reactivity isn't increased with more empty spots in valence shell?

If from a geometric perspective the non-halogens, non-noble gases have more empty spots in their valence shell, and the filling/exiting of any of the empty spots in the shell constitutes a...

03 August 2024 4,787 2 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

How to scrape off the surface layer of compound sputtering targets as with multiple usage top layer's stoichiometry changes from the original target?

I am experiencing this for the Bi2Se3 sputtering target. Initially, even if the target was 2:3 in Bi : Se, with a few sputtering runs, due to the high escaping tendency of selenium, the top layer...

23 July 2024 1,649 1 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

Differences between Surface Tension and Interfacial Tension in Liquid-Gas Phases?

Hi everyone, I have a question regarding surface and interfacial tension. Although I understand that these tensions are studied for different purposes, can they be considered equivalent in the...

18 July 2024 382 5 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

Roughening Silver Electrode Using CH Instruments for SERS applications?

I am in the process of roughening a silver electrode for SERS measurements using the latest version of CH Instruments. Most procedures in the literature mention sweeping the potential from -0.3 V...

30 June 2024 4,639 3 View

How closely does an elastic sheet conform to what's below it?

See the attached file for an illustration of this problem. Consider an elastic sheet S (orange) that’s laying atop a solid base B (blue). The sheet is under tension (arrows) and is held to the...

30 June 2024 747 4 View