In IDA, for every increment of intensity of loading ,the drift values will be maximum at the same point or it may at any poiny ?

28 February 2018 1 8K Report

Because in my case, for 10 storied RC frame, drift values are coming maximum at the same node for every increase of intensity.

Punashri Prakash Phadnis

It may be at any point. It is required to be check.

Badges
Science topic

Similar topics
Phytochemistry
Extracts

More Vishvas Patil's questions See All

How to estimate sample size for GWAS of continuous and discrete traits? What are the pre-requisites?

Genome-wide association study (GWAS) Continuous traits: eg. Height Discrete traits: eg. Eye color

28 July 2024 286 0 View

Can we fit a gaussian Fit on a LIBS Peak ?

Though much literature suggests fitting a Voigt profile on a LIBS peak, is it also possible to fit a Gaussian profile on the LIBS peak? I have 204 spectra files, and I am building a pipeline for...

23 July 2024 6,127 1 View

Why is my phage library obtained at round 2 of Biopanning viscous?

After incubation of the TG1 cells with the helper phage, I spun down the culture and precipitated the supernatant with PEG/NaCl. After this, I spun it down again and resupended the pellet in PBS....

21 June 2024 6,260 2 View

Can we use LIBS Peak - Ti 441.492 for the Univarate Analysis ?

I have 17 different steel samples, in which i identified a peak of Ti 441.492. But , if you look closely at photo, while some some peak are at 441.492 , some are at the slight offset. eg 441.490...

10 June 2024 8,934 2 View

Challenges in Univariate Analysis for Stainless Steel Samples using Laser Induced Breakdown Spectroscopy?

Respected Members , I have a 17 different steel sample references , with varying concentration for Minor Elements being Mo , Ni , Mn ,Si , Cr etc , i am trying to build a calibration curve with...

10 June 2024 993 0 View

Normalization in LIBS Spectra ?

Hello Everyone ! I have a samples a satinless steel , I performed the LIBS Measurement with hLIBS (SciAps Z-300). Total of 12 measurements on different locations were done on the same sample...

09 May 2024 7,959 6 View

Is IJSREM UGC Care or cloned journal?

Some journals seems to be fake..cloned

07 May 2024 3,623 1 View

Does anyone know about Universities offering (a) PhD by prior publication or (b) PhD by portfolio?

Dear Colleagues, Does anyone know about Universities that are offering (a) Ph.D. by prior publication (b) Ph.D. by portfolio? I have two publications viz."Regression Testing in Era of Internet of...

09 April 2024 2,123 1 View

How to calculate chemical quantity required when relative molar composition is given ?

Relative molar composition of 1.0 TEOS : 0.2 CTACl : 0.0026–0.017 LS277 dye : 10.4 TEA : 142 H2O was used.

04 April 2024 6,770 1 View

What are usual pumping and heating costs in the refineries?

As heat exchangers in the heat exchanger networks get fouled, the utility in the furnace has to increased to compensate the losses. Apart from it, the pumping cost must be increasing as deposited...

04 February 2024 531 3 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

Using a large amount of data, such as 30 years of daily data, in a machine learning model like LSTM can reduce the model predictivity?

I have used 30 years of daily data, but the model is not able to optimize, getting just 0.57 in NSE and R2. when I reduced the data to 20 years in daily time frame I got 0.73 in NSE, R2 for both...

22 July 2024 669 0 View

What is the the target displacement for a retrofitted model outside US conditions (preferably Indian conditions)?

Dear Members of ResearchGate, I hope you are doing well. I have been retrofitting using the ASCE 41 2017 standard. In it, I have two basic doubts. 1. The target displacement as per clause...

13 June 2024 2,773 0 View

How to find out hysteretic energy consumption of the pier after earthquake excitation in sap?

how to observe the hysteretic energy consumption for a parrticular frame element

12 June 2024 3,426 1 View

How can I see the modes of vibrating in a 3D model with opensees?

Hi, I am calculating the periods of a steel building modeled as a 3D moment frame. Is there any script to display the shape of vibrating of the model in opensees?

12 June 2024 8,065 1 View

Adding a frame element into an OpenSees model after running initial?

Hi, I am running an opensees model of a 2-bay 1-storey frame with settlement at the mid-support. I wanted to add an additional frame element as a bracing to the analyzed frame after it sustains...

08 June 2024 4,132 0 View

How can I calculate average dG MM/GBSA energy from selected frames of MD trajectories?

I need to calculate dG MM/GBSA energy through the MD simulation trajectories. From RMSD values I selected last 400 frames from MD trajectories. I ran thermal_mmgbsa.py script, but it calculates dG...

22 May 2024 10,076 5 View

How to express spinors with an arbitrary change of coordinates?

A spinor field in classical differential geometry is defined as a section of a spinor bundle, which is by definition the associated bundle constructed from the spinor representation and the...

14 May 2024 400 0 View

Why do I get frameshift mutants in antibody phage display?

I'm performing an antibody phage display with a VHH library and I consistently get frameshift mutants (mainly frame +2) after biopanning. I'm using TG-1 cells for amplification of phagemids and...

14 May 2024 412 2 View