·
In Extrusion process, it is evident that the extruded section was bent due to the material micro-structural and forming interface condition related factors. From application point of view, how such a problem could be properly addressed
Good monrng, general question, more details is need to be shares. Material? Process description? Required output? Thank you.
yess
I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...
08 August 2024 4,812 2 View
this is based on the book of African Christian Ethics by Samuel W. Kunhiyop
28 May 2024 8,980 3 View
We crossed SynCre mice with Tg403-loxp-rtTA mice, but all the pups ended up with either one of the genes, not both together, as confirmed by genotyping tests. Has this ever happened to anyone else?
15 May 2024 3,964 2 View
We are doing simulations of fdsoi ncfet in synopsis tcad can someone correctly explain how to match the ferroelectric capacitance and mos capacitance
06 March 2024 7,511 0 View
I am simulating a tension test of a bimaterial specimen in ABAQUS. I would like to create different field outputs for each material, and I would like to display them in a single contour plot. For...
20 January 2024 4,613 4 View
I would like to know if it is a common reagent kit for the target amplification of both DNA and RNA, or does it show amplification only for the RNA targets. Will the presence of DNA in the sample...
18 December 2023 7,062 2 View
I have transfected cells with vector containing my protein of interest which has a Flag tag. The expression is inducible. When I run western blot, I see flag in my transfected induced cells as...
21 September 2023 3,996 3 View
Currently, I am working on algae-based wastewater treatment. in order to check the effect of various parameters towards treatment efficiency, I want to vary the COD, Nitrate, Nitrite, and...
13 September 2023 3,584 3 View
How it enhance acedemic or industrial career? thanks in advance
29 August 2023 2,899 3 View
Recently I submitted the SCAPS simulated manuscript to one of the RSC journals and I have taken some of the parameters from the literature as all the SCAPS papers have done the same. can anyone...
15 August 2023 2,560 0 View
I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...
07 August 2024 1,686 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...
07 August 2024 3,218 4 View
Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...
06 August 2024 666 4 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...
23 July 2024 10,032 0 View
Are both ways acceptable, or is there any convention to them? Thanks.
22 July 2024 6,988 4 View
Currently I need to calculate detection probabilities (PD) from radar cross section (RCS) data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0...
22 July 2024 868 0 View
Hi everybody, We are trying to write a systematic review meta-analysis paper. But I could find 19 references. I think 19 references are not enough to do a meta-analysis section and it is better to...
10 July 2024 5,490 5 View