Dear researchers,
Please help me out to learn about the fuzzy system from the scratch.
Please guide me with the steps and resources to follow .
Thanking you,
With regards,
Bhaskar Ghosh
Dear Bhaskar,
It 's a boat subject you pose here however i suggest to you a links and attached files in topics.
- Fuzzy Logic-Driven Resource Evaluation Method for Automated ...
link.springer.com/chapter/10.1007/978-3-662-45402-2_12
- Fuzzy Logic Experience Model in Human Resource Management ...
link.springer.com/chapter/10.1007/11552451_179
-Fuzzy Logic-Based Approaches in Water Resource System Modelling ...
link.springer.com/chapter/10.1007%2F978-3-540-79881-1_12
-Fuzzy Logic Resources.
uni-obuda.hu/users/fuller.robert/fuzs.html
-Fuzzy Logic Resources | Byte Craft Limited
www.bytecraft.com › Fuzzy Logic
-What are some good online resources to learn fuzzy logic? - Quora
https://www.quora.com/What-are-some-good-online-resources-to-l...
-Fuzzy Logic - IEEE Conferences, Publications, and Resources
technav.ieee.org/tag/3603/fuzzy-logic
-What Is Fuzzy Logic? - MATLAB & Simulink - MathWorks
https://www.mathworks.com/help/fuzzy/what-is-fuzzy-logic.html
Best regards
Respected Mohamed-Mourad Lafifi,
Thank you for your valuable guidance. I surely will follow these.
Thank you once again sir.
Regards,
Bhaskar
To start from scratch you may first read the book "Fuzzy Logic with Engineering applications" by Timothy Ross.
Book available at:
https://docs.google.com/file/d/0B5vXY4-Kg5GeMmg4U2N6ZlR4Qm8/edit
To start with, you may try to simulate a Fuzzy Logic based system with the Fuzzy Logic Toolbox available in MATLAB.
Then read some good research papers on Application of Fuzzy Logic in your problem domain.
Thank you very much madam for your valuable guidance.
Thanks a lot.
Thank you for giving me your precious time. My query is about the ways of reaching the researchers globally and opportunity to work with them. I have been working on modeling, characterization and...
09 October 2017 8,841 6 View
I need all kind of electronic components required to develop a robot, but the Radiation Hardened ones. Is there any available single board computer like Raspberry PI (for image processing), any...
08 September 2016 3,575 4 View
I am going to work on vision based robotic assembly with mainly pattern recognition. Planning to use 2 cameras. Where to start from and which things to be learnt? I know C and little bit of...
01 January 1970 3,297 5 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View