Does anyone know, can i do cryosectioning of whole aorta after oil red O staining and use the cryosection parts for further analysis?

I would like to quantify the lesions on aorta. I want to take image of atherosclerotic plaques formation in aorta by using O red Oil Solution. After the staining, what will be the storage...

16 February 2021 5,876 2 View

What is the best solution for counter electrode for perovskite solar cells at room conditions?

I'm investigating transparent counter electrode for FTO/PEDOT:PSS/MAPI3/PCBM layered perovskite solar cell. In my research lab, currently i have a glove box with N2 gas as a carrier. I'm goning...

21 December 2020 6,504 3 View

My status has changed from "Awaiting Reviewer Score" to Awaiting AE Decision". Could the Associate Editor reject the manuscript at this stage?

Otherwise what this status means. If the Editor has received the comments from reviewer then why he is not sending it to Authors. As 10 days already spent till the status changed.??

18 November 2020 6,252 4 View

How to adapt a mature Questionnaire?

I am looking forward to seek some help regarding adaptation of mature questionnaires. I am new to quantitative studies and wants to use some demographic in my questionnaire, is it necessary to add...

08 November 2020 7,146 5 View

Is there a way to isolate nuclei without purifying cytoplasmic protein aggregates?

Hello, I am trying to isolate nuclei from HEK293T cells expressing a protein that aggregates in the cytoplasm, however when I run my samples in western blot the cytoplasmic protein is strongly...

02 November 2020 9,541 3 View

How can i fill zinc oxide or titanium oxide into etched pattern on glass substrate?

Hi! I need zinc oxide or titanium oxide to be filled into etched area on glass sbstrate. Etched are is being photolithography processed and being dry etched. Material must not present around the...

25 October 2020 152 7 View

How to get the most out of your qPCR data?

23 October 2020 7,537 3 View

Do you think that the e-learning that took place after the COVID 19 crisis was fair for students to evaluate their knowledge?

The significance of the question is to know the extent of accuracy in evaluating students.

19 September 2020 3,663 13 View

How to calculate reliability for a newly launched system?

We have a hydraulic system (water collector and distributor) which is newly started, how can we calculate its reliability?

07 September 2020 6,619 2 View

Neonatal Renal dose adjustment! Guidelines or the reference that is most authentic in clinical practice.??

In the infants to the adult age group, we have been given a concrete guideline for dose adjustment on the basis of CKD-Stages or creatinine clearance. this pathway is missing in neonates but...

07 September 2020 1,731 3 View

Does any one know how i can prepare liver tissue with transmission electron microscope with good fixation?

i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity

03 March 2021 8,890 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

SEM or Multiple Regression for an analysis without Latent Variables?

Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...

26 February 2021 8,399 5 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View