No title

02 March 2021 932 1 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Tooth extraction and subsequent dental implant placement in Sprague-Dawley rats induce differential changes in anterior digastric myofibre size and ?

01 March 2021 7,254 3 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

SSR primers are species specific or we can use it for any plant species ?

Hi, any one please guide me; SSR primers are species specific or trait specific. i have few primer which was reported in articles for wheat yield can i use these similar primer for lentil yield...

20 February 2021 315 4 View

Solution of 2D convection diffusion heat equation using MATLAB ?

This is a polymer heating problem. Polymer enters at around 180C (x=0) in the barrel. Also barrel initial temperature is 180 (t=0). Some heat Is added along whole length of barrel q. We have to...

15 February 2021 3,887 1 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

How to get actual or true SoC while predicting SoC for Batteries using Data Driven Approaches?

I have seen it in multiple research articles that authors use certain approaches to predict electric vehicle battery's state of charge(SoC) and then they compare it with battery's true SoC. So I...

11 February 2021 9,070 3 View

Ligands with 3,4,5-trihydroxyphenyl group?

Hi In the design of a bidentate ligand with imine group, is it okay to have a 3,4,5-trihydroxyphenyl group in the structure? In other words, does the 3,4,5-trihydroxyphenyl group compete with...

08 February 2021 4,977 7 View

How to get/count refractive index in gasses?

20 February 2021 8,202 6 View

Want to ask about equivalence ratio?

09 February 2021 5,273 2 View

Can someone help me to improve the MCF-10A growth?

18 January 2021 7,640 3 View

In Michaelis-Menten Kinetics, why K(subscript)On have units (mol^-1)(time^-1)?

where K(subscript)On is the rate of Enzyme (E) + Substrate (S) going to Enzyme-Substrate complex (ES). I think I understand why K(subscript)Off and K(subscript)catalysis have units of time^-1....

11 January 2021 649 8 View

Do chemical and physical properties influence on the size of a polymer particle?

I would like to know if the properties of a polymer impact on the size of the particle it forms. I'm working with different polyssacharides (alginic acid from different seaweed), which are...

29 December 2020 7,333 6 View

How to make solution with molar ratio 1:40?

Currently i'm working to develop encapsulation using ferritin, based on many journals they always wrote the molar ratio between drugs and ferritin, for example 1:40, how to know the molarity that...

22 December 2020 6,582 2 View

Having issues understanding the particles/mL to molarity conversion, I've seen many different way but non of them seem to match one an the other?

I have 68nm spherical Au NPs, which gave me a concentration of 1.22 x 10^9 particles/mL. How can I calculate the molarity without the need for TEM?

22 November 2020 8,850 3 View

What solvent can I use to prepare a higher concentration of 5-Bromouracil?

I am standardizing a UHPLC method for separation of thioguanine phosphate metabolites. For this, I want to use 5-Bromouracil (5-BU) as an internal standard, however I am unable to prepare solution...

15 November 2020 4,982 3 View

How storage capacity for clathrate hydrate is calculated?

Storage capacity of hydrate solely depends on molar volume of empty hydrate lattice because rest of the terms get canceled (even moles of gas consumed). However, if we take temperature constant,...

16 October 2020 720 2 View

Please suggest that the way of obtaining the concentration (in mol) from the gas mixture (N2=98%, Ethylene=1% and Butadiene=1%) is correct or not?

I have a gas mixture (N2=98%, Ethylene=1% and Butadiene=1%). I want to obtained the molar concentration of each components for 1mL volume of the gas mixture. For that purpose, I have used the...

29 September 2020 6,233 1 View