How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

Steps to calculate activation energy by coats & redfern method?

I'm a chemistry student and I'm researching the kinetic degradation of mixed plastic waste. I'm having trouble calculating the activation energy by the coats & Redfern method. The data that...

24 February 2021 974 1 View

Droplet PCR in plastic chips always result an unexpected band, any suggestion of possible contaminations and how to improve?

I am doing droplet based digital PCR inside plastic chips. I can get the correct band, but I also consistently get an unexpected band, slightly shorter. I attached a typical gel image here....

18 February 2021 6,618 2 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

How to measure the hardness for PLA & PHAs polymers?

Hello, I am a bit confused on whether to follow ASTM D785 (Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials) or ASTM D2240 (Standard Test Method for...

21 January 2021 7,487 4 View

Where can I find stress-strain data for steel to define plastic properties in Abaqus?

I am looking for stress-strain data for steel to input for the plastic properties in Abaqus. However I cannot find any literature or experimental data on the matter. If full data is not available...

15 January 2021 9,070 2 View

Hi, could anyone help me knowing which kind of Diamond blade would be better to cut thermoplastic composite?

The blade that could cut ceramics, or the one that could cut plastics and polymers?

06 January 2021 2,713 3 View

Which module is preferred in Ansys software to simulate shrinkages of plastic powder for the Injection Molding (IM) process?

I need to know the effect of shrinkage of plastic powder materials by simulation using Ansys or Simufact software.

21 December 2020 5,693 9 View

Blow extrusion of PLA with the HDPE non rotary die. Is it possible?

Hello, I managed to run a small blown extrusion line, head diameter 70mm / screw 45mm. The machine is to be used for extrusion of sleeves from 200 to 500mm wide. Unfortunately, I have a draw...

13 December 2020 2,824 5 View

Which are the quality parameters considered for injection molded plastic products? And which inspection tools are used for the same ?

Quality parameters and inspection tools may differ from product to product. Please write whichever you know.

10 December 2020 1,478 2 View

Will i need to define ductile damage parameters as well as yield stress vs plastic strain values for performing Fire-tensile test of CFRP/GFRP BARS?

Can someone please help me in this regard ... i have modelled a CFRP/GFRP( elastic and plastic properties together with temperature dependent -mass density, thermal conductivity and specific heat)...

03 December 2020 5,435 3 View