I want extarct and quantifiy the Lecithin, Bees wax and soft paraffin wax in cosmetic cream. How I can proceed?

07 April 2017 1 769 Report

I want try with FTIR-ATR, by extracting in chloroform. Lecithin, Bees wax share same chemical nature (fatty ester group) so I’m thinking I may not successful by approach?. Please anybody help me solve this problem.

Umesha S S.

HI Shakeel,

Thanks for your Answers. I will consider this idea.

Badges
Science topic

More Umesha S S.'s questions See All

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

Which is the best software or programming language (user friendly) for analysing data?

I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...

20 February 2021 3,950 15 View

Hi..how to isolate crude HDL (all subfractions) from human serum by size exclusion chromatography?

I would like to know about isolation of crude HDL from serum by SEC. Is it possible to perform with a serum sample volume of

19 February 2021 5,576 2 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View

Do you have any experience with transfection of EBV immortalized B cells with Lipofectamine?

I know that efficiency of transfection for primary B cells is very low with Lipofectamine. But I did not try that for EBV immortalized B cells. Do you have any experience with transfection of EBV...

05 February 2021 4,159 1 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View