I optimize molecule in gas phase in gaussian , used this optimize geometry for solvent state while doing ftir , uv, dos. is this procedure correct if not what to do? If anyone know help me please?
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,992 0 View
I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...
03 August 2024 3,851 1 View
I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...
03 August 2024 6,070 3 View
HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...
31 July 2024 5,309 7 View
I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...
31 July 2024 9,697 0 View
In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?
28 July 2024 2,988 0 View
Please suggest basic literature on lattice-based cryptography. A kind response from the cryptographic community will be highly appreciated.
24 July 2024 6,291 4 View
I want to know that n-doped side of solar cell is connected with positive or negative electrode.
20 July 2024 1,348 2 View
Bioinformatics tools like peptide cutter
15 July 2024 6,453 1 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View
I need to do some experiment with it in liquid form.
07 August 2024 613 3 View
The first pdf file I uploaded had an error. So I uploaded an updated, corrected pdf of that paper with a different pdf name. I dpon't want the old copy to be download or read.
07 August 2024 9,508 1 View
I work on MCF7 cell cell for anticaner purpose and I wa to do drug preperation the drug ( secondary metabolites extracted from Aspergillus) My question which solvent is better with these secodary...
03 August 2024 4,725 2 View
I'm trying to calculate the tolerance factors of the hydride perovskite and the value calculated by me and the reported values are contradictory. Need more clarity in using the correct ionic radii...
01 August 2024 2,614 1 View
Hello everyone, I need to dissolve stigmasterol for an animal experiment, but it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent for stigmasterol?
01 August 2024 7,504 2 View
How to change the displayed full article text to its corrected version? In the file on the page of the journal where I published the article, there was an error in the text, the table is...
30 July 2024 3,229 2 View
The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...
30 July 2024 3,126 0 View
I am writing to request a correction regarding the affiliation of one of my co-authors, Donald Ho. Currently, the author's profile incorrectly lists an affiliation with The Hong Kong Polytechnic...
28 July 2024 6,824 0 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...
27 July 2024 5,748 0 View