Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Monte Carlo simulation?

Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...

22 February 2021 3,680 4 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

Which is the best software or programming language (user friendly) for analysing data?

I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...

20 February 2021 3,950 15 View

Hi..how to isolate crude HDL (all subfractions) from human serum by size exclusion chromatography?

I would like to know about isolation of crude HDL from serum by SEC. Is it possible to perform with a serum sample volume of

19 February 2021 5,576 2 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is the most suitable server for predicting protein structures in bacteria?

I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...

28 February 2021 4,521 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

How to calculate the crystallinity of cellulose film?

27 February 2021 2,753 4 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View